PUSH-BUTTON START OPERATION CHECK

OPERATION DESCRIPTION
1. Push-button start function:
  1. When the key is in a detection area inside the vehicle and the brake pedal is depressed, the engine is started by pressing the engine switch.
  2. When the key is in a detection area inside the vehicle and the brake pedal is not depressed, the power source mode is changed by pressing the engine switch. The power source mode changes in the following order every time the engine switch is pressed: off → on (ACC) → on (IG) → off.
  3. After getting into the vehicle while carrying the key when the engine switch is off, if the engine switch is pressed while not depressing the brake pedal, the power source mode changes to on (ACC).
  4. After getting into the vehicle while carrying the key when the engine switch is off, if the engine switch is pressed 2 times without depressing the brake pedal, the power source mode changes to on (IG).
  5. Text in Illustration
    
    *a Entry Warning Light displayed
    
    After getting into the vehicle while carrying the key when the engine switch is off, if the brake pedal is depressed while the shift lever is in P or N, the entry warning light is displayed.
  6. The engine starts if the engine switch is pressed when the entry warning light is displayed.
2. Changing the power source mode when the key does not operate correctly due to wave interference or key battery depletion:
  1. Unlock the door using the built-in mechanical key and get into the vehicle while carrying the key.
  2. While depressing the brake pedal, and facing the logo side of the key towards the engine switch, hold the key near the engine switch.
  3. A buzzer in the combination meter assembly sounds and the power source mode changes to on (IG). Pressing the engine switch without depressing the brake pedal turns the power source mode from on (IG) to off.
3. Starting the engine when the key does not operate correctly due to wave interference or key battery depletion:
  1. Unlock the door using the built-in mechanical key and get into the vehicle while carrying the key.
  2. While depressing the brake pedal with the shift lever in P or N*, while facing the logo side of the key towards the engine switch, hold the key near the engine switch.
    
    Tech Tips
    
    *: This is only applicable when the steering wheel unlocked.
  3. A buzzer in the combination meter assembly sounds, the power source mode changes to on (IG) and the entry warning light is displayed.
  4. Press the engine switch with the brake pedal depressed to start the engine.

Text in Illustration
*a	Entry Warning Light displayed

CHECK PUSH-BUTTON START FUNCTION

Check the push-button start function:
1. Get into the vehicle while carrying the key with the engine switch off. With the shift lever in P, check the entry warning light is displayed when the brake pedal is depressed. Then check that the engine starts when the engine switch is pressed after the entry warning light is displayed.
2. While the brake pedal is released and the key is being carried, check that the power source mode changes in the following order when the engine switch is pressed: off → on (ACC) → on (IG) → off.
  
  Tech Tips
  
  When the engine switch is pressed with the engine switch on (IG) and the shift lever not in P, the power source mode does not change to off, but changes to on (ACC).
3. With the shift lever in P, check that the steering lock operates when a door is opened.
  
  Tech Tips
  
  When the engine switch is pressed after the vehicle is stopped, the engine stops and all the power turns off. However, if the shift lever is not in P when the engine switch is pressed with the vehicle stopped, the power source mode does not change to off, but changes to on (ACC).
4. Text in Illustration
  
  *a Inspection Point
  
  Check the push-button start function operation range for the front side. Place the key in either of the two locations making sure that the key is oriented as shown in the illustration, and then check that the engine can be started.
  Note
  - Even if the key is in a vehicle interior key detection area, the key may not be properly detected if the key is on the instrument panel, in the glove box or on the floor.
  - If the key is within 0.2 m (0.66 ft.) of the shift lever, communication may not be possible.
  Tech Tips
  
  Perform this inspection for both inspection points.
5. Text in Illustration
  
  *a Inspection Point
  
  Check the push-button start function operation range for the rear side. Place the key in either of the two locations making sure that the key is oriented as shown in the illustration, and then check that the engine can be started.
  Note
  - Even if the key is in a vehicle interior key detection area, the key may not be properly detected if the key is on the instrument panel, in the glove box or on the floor.
  - If the key is within 0.2 m (0.66 ft.) of the center of the rear seat, communication may not be possible.
  Tech Tips
  
  Perform this inspection for both inspection points.
Check the key lock-in prevention function (inside luggage compartment).
1. Place the electrical key transmitter sub-assembly in the luggage compartment with all doors locked. Check that: 1) closing the luggage compartment door triggers the key wireless buzzer (which lasts approximately 2 seconds), and 2) pressing the luggage electrical key switch opens the luggage compartment door.
2. Text in Illustration
  
  *a Inspection Point
  
  Inspect the key lock-in prevention detection area. Pay attention to the direction of the electrical key transmitter sub-assembly shown in the illustration. When the electrical key transmitter sub-assembly is in either of the 2 locations in the illustration, check that: 1) closing the luggage compartment door sounds the wireless buzzer, and 2) pressing the luggage electrical key switch opens the luggage compartment door.
3. Text in Illustration
  
  *a 0.1 m or more (0.328 ft. or more)
  
  Inspect the key lock-in prevention detection area and the door control receiver for wave leaks. Hold the electrical key transmitter sub-assembly at the same height as the lower edge of the luggage compartment door aligning it with the center of the rear of the vehicle. Pay attention to the direction and position of the electrical key transmitter sub-assembly shown in the illustration.
  Tech Tips
  - When the electrical key transmitter sub-assembly is over 0.1 m (0.328 ft.) from the rear bumper, the wireless buzzer does not sound.
  - If the warning buzzer sounds, the No. 3 indoor electrical key antenna (inside luggage compartment) may have a wave leak.
Check the key lock-in prevention function (vehicle interior).

Note

In order to prevent the electrical key transmitter sub-assembly from being locked inside the vehicle, perform this inspection with the window of a door open.
1. Turn the engine switch off.
2. Place the electrical key transmitter sub-assembly on a front or rear seat.
3. Close the door, making sure the doors are unlocked.
Check the push-button start cancel function.
1. Cancel the push-button start and check that all the functions of the push-button start no longer operate.
  Tech Tips
  - Refer to the following procedures to cancel the push-button start Click here.
  - While the push-button start is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.
2. While the key cancel function (entry cancel function) is on, check that all functions of the push-button start cannot be operated.

Text in Illustration
*a	Inspection Point

Text in Illustration
*a	Inspection Point

Text in Illustration
*a	Inspection Point

Text in Illustration
*a	0.1 m or more (0.328 ft. or more)

Check the answer-back function (hazard warning light flashing).

Entry Operation	Hazard Warning Light
Entry Door Lock	Flashes once
Entry Door Unlock	Flashes twice

KEY DIAGNOSTIC MODE (Using GTS)

Tech Tips

With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the wireless buzzer.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

Enter the following menus: Body Electrical / Entry & Start / Utility / Communication Check (Key Diag Mode).

Inspect the appropriate item according to the following table.

Tester Display	Inspection Item
[CH1/CH2] Overhead + Driver Side	No available
[CH1] Overhead + Driver Side
[CH2] Overhead + Driver Side
[CH1/CH2] Overhead + Passenger Side	No available
[CH1] Overhead + Passenger Side
[CH2] Overhead + Passenger Side
[CH1/CH2] Overhead + Rear LH Side	No available
[CH1] Overhead + Rear LH Side
[CH2] Overhead + Rear LH Side
[CH1/CH2] Overhead + Rear RH Side	No available
[CH1] Overhead + Rear RH Side
[CH2] Overhead + Rear RH Side
[CH1/CH2] Overhead + Front Room*1	No. 1 indoor electrical key antenna assembly (front floor)
[CH1] Overhead + Front Room*1
[CH2] Overhead + Front Room*1
[CH1/CH2] Overhead + Rear Room*2	No. 2 indoor electrical key antenna assembly (rear floor)
[CH1] Overhead + Rear Room*2
[CH2] Overhead + Rear Room*2
[CH1/CH2] Overhead + Luggage	No available
[CH1] Overhead + Luggage
[CH2] Overhead + Luggage
[CH1/CH2] Luggage + Luggage (inside)*3	No. 3 indoor electrical key antenna assembly (inside luggage compartment)
[CH1] Luggage + Luggage (inside)*3
[CH2] Luggage + Luggage (inside)*3
[CH1/CH2] Luggage + Luggage	No available
[CH1] Luggage + Luggage
[CH2] Luggage + Luggage
[CH1/CH2] Immobiliser Amp*4	Amplifier (engine switch)
[CH1] Immobiliser Amp*4
[CH2] Immobiliser Amp*4

[CH1]: Channel 1 is set.
[CH2]: Channel 2 is set.
[CH1/CH2]: Channel 1 and 2 switches automatically at a specific interval*.

*: If the electrical key transmitter sub-assembly is detected with either channel 1 or 2, the buzzer sounds.

Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless door lock buzzer sounds.

Tech Tips

The buzzer sounds in short, repeated beeps for all items except "Overhead + Rear Room"*2. For "Overhead + Rear Room"*2, the buzzer sounds in one long, continuous beep.
Text in Illustration

*a Inspection Point

*1: No. 1 indoor electrical key antenna assembly (front floor)

Tech Tips

Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.
Text in Illustration

*a Inspection Point

*2: No. 2 indoor electrical key antenna assembly (rear floor)

Tech Tips

Place the electrical key transmitter sub-assembly on the rear seat cushion.
Text in Illustration

*a Inspection Point

*3: No. 3 indoor electrical key antenna (inside luggage compartment)

Tech Tips

Place the electrical key transmitter sub-assembly in the luggage compartment. Even if the electrical key transmitter sub-assembly is in the luggage compartment, the buzzer may not sound.
*4: Amplifier (engine switch)

Tech Tips

While facing the logo side of the electrical transmitter sub-assembly towards the engine switch, hold the transmitter near the engine switch.

CHECK TRANSMITTER BATTERY SAVING FUNCTION
1. Check the transmitter battery saving function:
  1. Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.
  2. Check that the push-button start does not operate while in transmitter battery saving mode.
    
    Tech Tips
    
    To cancel transmitter battery saving mode, press a button of the electrical key transmitter sub-assembly.

Text in Illustration
*a	Inspection Point

Text in Illustration
*a	Inspection Point

Text in Illustration
*a	Inspection Point

CHECK POWER SOURCE MODE CHANGING FUNCTION

Check the engine switch.

Check that the power source mode changes according to the chart below.

Shift Position	Brake Pedal	Power Source Mode when Engine Switch Pressed
P	Released	Off → on (ACC) → on (IG) → off
P	Released	Engine running → off
P	Released	On (ACC)*1 → off
P	Depressed	Off → engine starts
P	Depressed	On (ACC) → engine starts
P	Depressed	On (IG) → engine starts
P	Depressed	Engine running → off
P	Depressed	On (ACC)*1 → off
N	Released	Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time engine switch is pressed)
N	Released	Engine running → on (ACC)
N	Depressed	Off → engine starts*2
N	Depressed	On (ACC) → engine starts*2
N	Depressed	On (IG) → engine starts*2
N	Depressed	Engine running → on (ACC)
Not P or N	Released	Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time engine switch is pressed)
Not P or N	Released	Engine running → on (ACC)
Not P or N	Depressed	Off → on (IG)
Not P or N	Depressed	On (ACC) → on (IG)
Not P or N	Depressed	Engine running → on (ACC)

Tech Tips

*1: This situation is only applicable when the power source mode has changed from on (IG) to on (ACC). However, this situation is not applicable when an emergency stop is performed by pressing and holding the engine switch for 2 seconds or more or by quickly pressing the engine switch 3 times or more.
*2: This situation is only applicable when the steering is unlocked.

CHECK POWER SOURCE MODE INDICATION

Text in Illustration
*a	POWER ON display
*b	Entry Warning Light display

Check the entry warning.

Multi-information Display Inspection
Power Source Mode	Multi-information Display
Off (Excluding condition in which the engine can be started)	Off
On (ACC) (Excluding condition in which the engine can be started)	"POWER ON" displayed
On (IG) (Excluding condition in which the engine can be started)	"POWER ON" displayed
Condition in which engine can be started*1	Entry Warning light displayed
Engine started	Off

Tech Tips

*1: Indicates the condition in which the engine can be started by pressing the engine switch while either of the following conditions is met:

Condition 1

All of the following conditions are met:

The power source mode was turned from on (IG) to on (ACC).
Key verification is OK*2 or immobiliser is unset (engine switch is on (ACC) or on (IG)).
The shift lever is in N and the steering is unlocked.
The stop light switch is on.

Condition 2

All of the following conditions are met:

The power source mode was not turned from on (IG) to on (ACC).
Key verification is OK*2 or immobiliser is unset (engine switch is on (ACC) or on (IG)).
The stop light switch is on.
The shift lever is in P, or the shift lever is in N with the steering unlocked.

*2: When the key is in the vehicle, the ID code sent as a result from communication between the key and certification ECU (smart key ECU assembly) and the ID code calculated by the certification ECU (smart key ECU assembly) are compared. If the ID codes match each other, the vehicle recognizes that the key is in the vehicle.