ENTRY AND START SYSTEM (for Start Function) CUSTOMIZE PARAMETERS

CUSTOMIZE ENTRY AND START SYSTEM (for Start Function)

1. Customizing with the GTS

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the engine switch on (IG).

   3. Turn the GTS on.

   4. Enter the following menus: Customize / Entry&Start or Warning.

   5. Select the setting by referring to the table below.

      Entry&Start

      Display	Default	Content	Setting	Relevant ECU
      Ignition Available Area (Entry ignition available area)	All	Function that sets the area that the key must be in before the engine switch can be operated.	Front or All	Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW	OFF	Function that enables or disables the entry and start system.	OFF or ON
      Engine Start Indicator	ON	Function that turns the entry warning light on the combination meter assembly on or off.	OFF or ON

      Warning

      Display	Default	Content	Setting	Relevant ECU
      Key Low Battery Warning (Warn when key battery becomes weak)	ON	Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.	OFF or ON	Certification ECU (smart key ECU assembly)

2. Customizing with the Accessory meter assembly*1 or Multi-display*2

   
   

   • *1: for 12.3 Inch

   • *2: 8 Inch

   
   

   1. Turn the engine switch to ON.

   2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Setting.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Entry and start system	On	Function that enables or disables the entry and start system.	On or Off	Certification ECU (smart key ECU assembly)

3. Entry cancel function (manual operation)

   Tech Tips

   While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.

   
   

   1. The following functions are disabled when the entry and start system is canceled.

      
      

      1. Entry unlock/lock functions

      2. Entry luggage compartment door open function

      3. Push-button start function

      4. Key lock-in prevention function

      5. Entry warning functions

   2. When canceling the system through manual operation:

      
      

      1. Make sure the following conditions are met:

      
      

      • The engine switch is off.

      • The driver door is closed.

      • The driver door is unlocked.

      2. Press the unlock switch of the electrical key transmitter sub-assembly.

      3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).

      4. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

         Note

         If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).

      6. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times completing the step above.

         Note

         If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).

      8. Close the driver door within 5 seconds of completing the above step.

      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

      Tech Tips

      Finish the step 5 to 7 within 30 seconds.

   3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.

      
      

      1. Perform the procedures to cancel the entry and start system again.

      2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

         Tech Tips

         
         

         • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

         • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.