FRONT DOOR LOCK INSPECTION


  1. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

    A01FIF6E11
    Text in Illustration
    *a Lock *b Unlock
    *c

    Component without harness connected

    (Front Door Lock Assembly LH)

    - -

    1. Check the door lock motor operation.


      1. Apply battery voltage to the motor connector and check the operation of the front door lock motor.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 4 (L)

        Battery negative (-) → 1 (UL)

        Lock

        Battery positive (+) → 1 (UL)

        Battery negative (-) → 4 (L)

        Unlock

        • If the result is not as specified, replace the front door lock assembly LH.

    2. Check the detection switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        8 (LSSR) - 7 (E) Lock 10 kΩ or higher
        8 (LSSR) - 7 (E) Unlock Below 1 Ω

        • If the result is not as specified, replace the front door lock assembly LH.

    3. for LHD:

      A01FI2SE15
      Text in Illustration
      *a Unlock *b Off
      *c Lock *d

      Component without harness connected

      (Front Door Lock Assembly LH)


      1. Check the door lock and unlock switch.


        1. Measure the resistance according to the value(s) in the table below.

          Standard Resistance
          Tester Connection Condition Specified Condition
          9 (L) - 7 (E) Lock Below 1 Ω

          9 (L) - 7 (E)

          10 (UL) - 7 (E)

          OFF 10 kΩ or higher
          10 (UL) - 7 (E) Unlock Below 1 Ω

        • If the result is not as specified, replace the front door lock assembly LH.

  2. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

    A01FJ0GE15
    Text in Illustration
    *a Lock *b Unlock
    *c

    Component without harness connected

    (Front Door Lock Assembly LH)

    - -

    1. Check the door lock motor operation.


      1. Apply battery voltage to the motor connector and check the operation of the door lock motor.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 4 (L)

        Battery negative (-) → 3 (UL)

        Lock

        Battery positive (+) → 3 (UL)

        Battery negative (-) → 4 (L)

        Unlock

        Battery positive (+) → 2 (DL)

        Battery negative (-) → 1 (UNDL)

        Set

        Battery positive (+) → 1 (UNDL)

        Battery negative (-) → 2 (DL)

        Unset

        • If the result is not as specified, replace the front door lock assembly LH.

    2. Check the detection switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        8 (LSSR) - 7 (E) Lock 10 kΩ or higher
        8 (LSSR) - 7 (E) Unlock Below 1 Ω

        • If the result is not as specified, replace the front door lock assembly LH.

    3. for LHD:

      A01FFUNE04
      Text in Illustration
      *a Unlock *b Off
      *c Lock *d

      Component without harness connected

      (Front Door Lock Assembly LH)


      1. Check the door lock and unlock switch.


        1. Measure the resistance according to the value(s) in the table below.

          Standard Resistance
          Tester Connection Condition Specified Condition
          9 (L) - 7 (E) Lock Below 1 Ω

          9 (L) - 7 (E)

          10 (UL) - 7 (E)

          OFF 10 kΩ or higher
          10 (UL) - 7 (E) Unlock Below 1 Ω

        • If the result is not as specified, replace the front door lock assembly LH.

  3. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

    A01FIUVE11
    Text in Illustration
    *a Unlock *b Lock
    *c

    Component without harness connected

    (Front Door Lock Assembly RH)

    - -

    1. Check the door lock motor operation.


      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 4 (L)

        Battery negative (-) → 1 (UL)

        Lock

        Battery positive (+) → 1 (UL)

        Battery negative (-) → 4 (L)

        Unlock

        • If the result is not as specified, replace the front door lock assembly RH.

    2. Check the detection switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        7 (LSSR) - 8 (E) Lock 10 kΩ or higher
        7 (LSSR) - 8 (E) Unlock Below 1 Ω

        • If the result is not as specified, replace the front door lock assembly RH.

    3. for RHD:

      A01FDNSE10
      Text in Illustration
      *a Unlock *b Off
      *c Lock *d

      Component without harness connected

      (Front Door Lock Assembly RH)


      1. Check the door lock and unlock switch.


        1. Measure the resistance according to the value(s) in the table below.

          Standard Resistance
          Tester Connection Condition Specified Condition
          6 (L) - 8 (E) Lock Below 1 Ω

          6 (L) - 8 (E)

          5 (UL) - 8 (E)

          OFF 10 kΩ or higher
          5 (UL) - 8 (E) Unlock Below 1 Ω

        • If the result is not as specified, replace the front door lock assembly RH.

  4. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

    A01FDXNE12
    Text in Illustration
    *a Unlock *b Lock
    *c

    Component without harness connected

    (Front Door Lock Assembly RH)

    - -

    1. Check the door lock motor operation.


      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 2 (L)

        Battery negative (-) → 1 (UL)

        Lock

        Battery positive (+) → 1 (UL)

        Battery negative (-) → 2 (L)

        Unlock

        Battery positive (+) → 4 (DL)

        Battery negative (-) → 3 (UNDL)

        Set

        Battery positive (+) → 3 (UNDL)

        Battery negative (-) → 4 (DL)

        Unset

        • If the result is not as specified, replace the front door lock assembly RH.

    2. Check the detection switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        7 (LSSR) - 8 (E) Lock 10 kΩ or higher
        7 (LSSR) - 8 (E) Unlock Below 1 Ω

        • If the result is not as specified, replace the front door lock assembly RH.

    3. for RHD:

      A01FHT0E06
      Text in Illustration
      *a Unlock *b Off
      *c Lock *d

      Component without harness connected

      (Front Door Lock Assembly RH)


      1. Check the door lock and unlock switch.


        1. Measure the resistance according to the value(s) in the table below.

          Standard Resistance
          Tester Connection Condition Specified Condition
          6 (L) - 8 (E) Lock Below 1 Ω

          6 (L) - 8 (E)

          5 (UL) - 8 (E)

          OFF 10 kΩ or higher
          5 (UL) - 8 (E) Unlock Below 1 Ω

        • If the result is not as specified, replace the front door lock assembly RH.