REAR DOOR LOCK INSTALLATION

Tech Tips

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart Click here.

INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
1. Install the rear door inside locking cable.
2. Attach the 3 claws to close the cover.
INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
1. Install the rear door lock remote control cable.
2. Attach the claw to close the cover.

INSTALL REAR DOOR LOCK ASSEMBLY LH

Note

When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
Do not allow grease or dust to contact the door lock wiring harness seal surface of the connector.
Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock assembly.

Apply MP grease to the sliding parts of the rear door lock assembly.
Install a new door lock wiring harness seal to the rear door lock assembly.

Text in Illustration
*A	w/o Double Locking System
*B	w/ Double Locking System

Insert the rear door lock assembly to the rear door outside handle frame release plate, and set it to the rear door panel.

Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.
Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

Torque:

5.5 N*m { 56 kgf*cm, 49 in.*lbf }
Connect the connector.

INSTALL REAR DOOR GLASS RUN LH
1. Finish installing the rear door glass run.

INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.
Connect the cable to the negative (-) battery terminal.
Operate the rear door window regulator so that the rear door glass can be installed.
Disconnect the cable from the negative (-) battery terminal.

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
Remove the rear power window regulator switch assembly with rear door armrest base panel.
Install the front side of the rear door glass run.

Text in Illustration
*1	MP Grease

Apply MP grease to the sliding area of the rear door glass channel as shown in the illustration.

Standard

Area	Specified Condition
A	122 mm (4.80 in.)
B	35 mm (1.38 in.)

Install the rear door glass channel to the rear door window regulator as shown in the illustration.

Note

Do not damage the door glass.

INSTALL REAR DOOR QUARTER WINDOW GLASS LH
1. Install the rear door quarter window glass.
INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH
1. Align the rear door glass run with the rear door rear lower window frame.
2. Insert the rear door rear lower window frame together with the rear door glass run into the front door panel.
3. Partially install the screw and 2 bolts.
4. Install the upper side of the rear door glass run.
INSTALL REAR DOOR SERVICE HOLE COVER LH
1. Apply new butyl tape to the rear door panel.
2. Text in Illustration
  
  *a Reference Point
  
  Pass the rear door inside locking cable and rear door lock remote control cable through a new rear door service hole cover, and then attach the rear door service hole cover using the reference points on the rear door panel.
  Note
  - Securely install the rear door service hole cover to prevent wrinkles and air bubbles.
  - There should be no wrinkles or folds after installing the rear door service hole cover.
  - After installing the rear door service hole cover, check the seal quality.
INSTALL REAR NO. 2 SPEAKER ASSEMBLY
1. Attach the clip to install the rear No. 2 speaker assembly.
  
  Note
  
  Do not touch the cone of the speaker.
2. Connect the connector.
INSTALL REAR DOOR ARMREST SET BRACKET LH
1. Install the rear door armrest set bracket with the 2 screws.
INSTALL REAR DOOR FRAME GARNISH LH
1. Attach the 2 clips to install the rear door frame garnish.
INSTALL REAR SIDE CURTAIN ASSEMBLY LH (w/ Rear Sunshade)
1. Attach the 2 clips and 4 claws to install the rear side curtain.
INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH
1. Install the rear door inner glass weatherstrip.
INSTALL REAR DOOR TRIM COVER LH
1. Attach the 6 clips to install the rear door trim cover.
INSTALL REAR DOOR NO. 1 STIFFENER CUSHION
1. Install the rear door No. 1 stiffener cushion.
INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
1. Connect the rear door lock remote control cable and rear door inside locking cable.
2. Connect each connector.
3. Text in Illustration
  
  *1 Reference Boss
  
  Attach the 3 claws to install the rear door trim board to the rear door inner glass weatherstrip.
4. Attach the reference boss in the direction indicated by the arrow in the illustration.
5. Attach the 8 clips to install the rear door trim board.
6. Install the 3 screws.
INSTALL REAR DOOR HOLE COVER
1. Install the rear door hole cover.
INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH
1. Attach the 3 claws to install the rear door inside handle bezel plug.
INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
1. Connect the connector.
2. Attach the 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.