G-BOOK SYSTEM (w/ Telematics Transceiver) Warning Notification Function Malfunction

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK PROBLEM SYMPTOM (WARNING NOTIFICATION FUNCTION)


    1. Check the problem symptom of the warning notification function.

      Result
      Result Proceed to
      The multi-display does not show a warning message even though a warning light turns on or the multi-information display indicates a warning. A
      The multi-display shows a warning message even though a warning light is not on and the multi-information display does not indicate a warning. B
      The multi-display shows a warning message different from the warning light or the multi-information display.
      The same warning notification is repeated. C

      Tech Tips


      • The warning notification function sends information to the G-BOOK center.

      • In order to determine if a temporary problem with radio waves caused the malfunction, carefully confirm the conditions that were present when the malfunction occurred.


    B

    INSPECT METER WARNING LIGHT Click here

    C

    CHECK NAVIGATION SYSTEM Click here

    A

  2. INSPECT WARNING LIGHT


    1. Check if the indicated warning light or message is listed in the following table.

      Tech Tips

      Only messages listed in the table are included in the G-BOOK warning notification function.

      Warning Name
      Engine warning
      Brake system warning
      ABS warning
      VSC warning
      Dynamic Rear Steering warning
      EPS warning
      VGRS warning
      Charging system warning
      Airbag warning
      PCS warning
      Cruise warning
      Lexus parking assist-sensor system open circuit warning
      LKA warning
      Entry and start system warning
      AFS warning
      Automatic headlight beam level control warning
      Automatic high beam warning
      4WD warning
      Electric parking brake warning
      Engine oil level warning
      Brake fluid warning
      Engine oil pressure warning
      Washer fluid level warning
      High coolant temperature warning
      Injector maintenance
      Result
      Result Proceed to
      Warning light or message is listed in the table. A
      Warning light or message is not listed in the table. B

    B

    END

    A

  3. CONFIRM SETTING (COMMUNICATION LOCK)


    1. Check if the G-BOOK communication lock is set.

      Result
      Result Proceed to
      Communication lock is not set. A
      Communication lock is set. B

    B

    RELEASE COMMUNICATION LOCK

    A

  4. CHECK FOR SERVICE FLAG


    1. Enter diagnostic mode Click here.

    2. A01FGYE

      Select "Service Information" on the Service Menu screen.

    3. A01FFPN

      Select "G-BOOK Information for Contract" on the Service Information screen.

    4. A01FHRHE01

      Using the illustration as reference, check if the flag information indicated by the arrow indicates "1".

      Result
      Result Proceed to
      "1" is indicated. A
      "1" is not indicated. B

    B

    RENEW DATA TABLE Click here

    A

  5. CHECK CONNECTION TO G-BOOK CENTER


    1. Turn the engine switch on (ACC) and wait 1 minute.

      A01FFRU

    2. Perform the operations shown in the illustration and check that G-BOOK.com is displayed.

      Tech Tips


      • If the G-BOOK.com screen is displayed, select "Renew" to check if it is possible to access the G-BOOK.com.

      • The screen illustrations provided are samples only and may be different from actual screens.

      Result
      Result Proceed to
      G-BOOK.com can be accessed. A
      G-BOOK.com cannot be accessed. B

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    OK

  6. INSPECT METER WARNING LIGHT


    1. Check if a warning light on the combination meter assembly comes on or a warning message on the multi-information display is displayed even when there is no problem.

      OK
      There are no problems with warning lights or warning messages.

      Tech Tips

      The warning notification function of the G-BOOK system uses the warning notification signals sent and received by the meter / gauge system. Therefore, if the meter / gauge system is not operating normally, the warning notification function will not operate normally.


    NG

    GO TO METER / GAUGE SYSTEM Click here

    OK

  7. CHECK CAN COMMUNICATION SYSTEM


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: System Select / CAN Bus Check.

    4. Check that all ECUs and sensors that use CAN communication are connected.

      Result
      Result Proceed to
      There are no connection problems. A
      There is a connection problem. B

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  8. CHECK DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Utility / All Codes.

    4. Check for DTCs Click here.

      Result
      Result Proceed to
      No DTCs are output. A
      DTCs are output. B
      DTCs cannot be checked.

    B

    INSPECT EACH ECU SYSTEM

    A

  9. CHECK NAVIGATION SYSTEM


    1. Check if the navigation system is operating and functioning normally.

      OK
      The navigation system is normal.

    NG

    GO TO NAVIGATION SYSTEM Click here

    OK

  10. RENEW DATA TABLE


    1. Renew the data.

      A01FGH2

      1. Perform the operations shown in the illustrations and select "Download necessary data".

        Tech Tips

        The screen illustrations provided are samples only and may be different from actual screens.

        Result
        Result Proceed to
        Data can be renewed. A
        Data cannot be renewed. B

    B

    CONTACT G-BOOK SUPPORT CENTER

    A

    END