POWER STEERING SYSTEM, Diagnostic DTC:C1528/12

DTC Code DTC Name
C1528/12 Motor Rotation Angle Sensor Malfunction

DESCRIPTION

The motor rotation angle sensor detects the motor rotation angle and sends this information to the power steering ECU.

DTC Code DTC Detection Condition Trouble Area
C1528/12 A motor rotation angle sensor malfunction.

  • Motor rotation angle sensor (built into power steering link assembly)

  • Harness or connector

  • Power steering ECU assembly

WIRING DIAGRAM

A01FGTME01

INSPECTION PROCEDURE

Note


  • If the power steering ECU assembly is replaced with a new one, perform assist map writing, clear the motor rotation angle sensor calibration value, initialize the motor rotation angle sensor value and calibrate the torque sensor zero point Click here.

  • If the power steering link assembly is replaced, clear the motor rotation angle sensor calibration value, initialize the motor rotation angle sensor value and calibrate the torque sensor zero point Click here.

PROCEDURE


  1. CHECK CONNECTORS


    1. Check the connection of the power steering ECU and power steering link connectors.

    2. Visually inspect the terminals of the power steering ECU and power steering link connectors.

      Result

      Result

      Proceed to
      Normal A
      Connectors not properly connected B
      Power steering ECU connector terminals abnormal C
      Power steering link connector terminals abnormal D

    B

    CONNECT CONNECTORS CORRECTLY

    C

    REPLACE POWER STEERING ECU ASSEMBLY Click here

    D

    REPLACE POWER STEERING LINK ASSEMBLY Click here

    A

  2. CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - MOTOR ROTATION ANGLE SENSOR)


    1. Disconnect the C2 motor rotation angle sensor connector.

    2. Disconnect the C7 power steering ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C2-2 (RZG) - C7-1 (RZG) Always Below 1 Ω
      C2-4 (RZCS) - C7-8 (RZCS) Always Below 1 Ω
      C2-1 (RZSN) - C7-7 (RZSN) Always Below 1 Ω
      C2-3 (RZV) - C7-3 (RZV) Always Below 1 Ω
      C2-2 (RZG) - Body ground Always 10 kΩ or higher
      C2-4 (RZCS) - Body ground Always 10 kΩ or higher
      C2-1 (RZSN) - Body ground Always 10 kΩ or higher
      C2-3 (RZV) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT POWER STEERING LINK ASSEMBLY (MOTOR ROTATION ANGLE SENSOR)


    1. Disconnect the C2 motor rotation angle sensor connector.

    2. A01FDOFE01
      Text in Illustration
      *a

      Component without harness connected

      (Motor Rotation Angle Sensor)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (RZSN) - 2 (RZG) Always 50 to 140 Ω
      3 (RZV) - 2 (RZG) Always 15 to 45 Ω
      4 (RZCS) - 2 (RZG) Always 50 to 140 Ω

    NG

    REPLACE POWER STEERING LINK ASSEMBLY Click here

    OK

  4. REPLACE POWER STEERING ECU ASSEMBLY


    1. Replace the power steering ECU assembly Click here.


    NEXT

  5. ASSIST MAP WRITING, INITIALIZE MOTOR ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT


    1. Perform assist map writing, clear the motor rotation angle sensor calibration value, initialize the motor rotation angle sensor value and calibrate the torque sensor zero point Click here.


    NEXT

  6. RECONFIRM DTC


    1. Clear the DTCs Click here.

    2. Start the engine.

    3. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1528/12 is not output A
      DTC C1528/12 is output B

    B

    REPLACE POWER STEERING LINK ASSEMBLY Click here

    A

    END