FRONT SEATBACK HEATER (for Sports Seat Type) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for Driver Side)


    1. A01FF5ME01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for Front Passenger Side)


    1. A01FGHZE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01FDXK

      Pass the 2 seatback cover brackets through the 2 holes of the separate type front seatback pad.

  3. INSTALL SEATBACK COVER WITH PAD (for Driver Side)


    1. Install the seatback cover with pad.

    2. A01FFE8E01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the seatback cover bracket with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:

      After the seatback cover bracket is attached, make sure the seatback cover bracket is not twisted.

    3. Attach the wire harness clamp.

    4. Attach the 4 claws to install the 2 front seat headrest supports.

    5. Attach the wire harness clamp.

    6. Attach the hooks.

    7. Connect the connector.

  4. INSTALL SEATBACK COVER WITH PAD (for Front Passenger Side)


    1. Install the seatback cover with pad.

    2. A01FFE8E01
      Text in Illustration
      *1 Seatback Cover Bracket

      Attach the 2 seatback cover brackets with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:

      After the seatback cover bracket is attached, make sure the seatback cover bracket is not twisted.

    3. Attach the wire harness clamp.

    4. Attach the 4 claws to install the 2 front seat headrest supports.

    5. Attach the hooks.

    6. Connect the connector.

  5. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A01FETH

    1. Slide the front seatback board sub-assembly LH upward to attach the 2 hooks and install it.

    2. Attach the 2 claws.

    3. Open the lower part of the front seatback board sub-assembly LH and install the 2 screws.

    4. Install the clip.

    5. Attach the hook to connect the rubber band.

    6. Connect the rubber band with the clip.

  6. INSTALL FRONT SEAT ASSEMBLY

    Click here

  7. CHECK SRS WARNING LIGHT

    Click here

  8. INSPECT SEAT BELT WARNING SYSTEM

    Click here

  9. INSPECT SEAT HEATER SYSTEM

    Click here

  10. INSPECT CLIMATE CONTROL SEAT SYSTEM

    Click here

  11. INSPECT POWER SEAT CONTROL SYSTEM

    for LHD: Click here

    for RHD: Click here

  12. ENABLE AUTOAWAY/RETURN FUNCTION (w/ Memory)


    1. Restore the autoaway/return function setting to the previous condition by changing the customize parameter Click here.