LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Sports Seat Type) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE FRONT SEAT ASSEMBLY

    Click here

  2. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. A01FEPU

      Using a clip remover, remove the clip and disconnect the rubber band.

    2. Detach the hook and disconnect the rubber band.

    3. Using a clip remover, remove the clip.

    4. A01FH5P

      Open the lower part of the front seatback board sub-assembly LH and remove the 2 screws.

    5. Push and slide the front seatback board subassembly LH to detach the claw.

      Tech Tips

      Use the same procedure to detach the claw on the other side.

    6. Slide the front seatback board sub-assembly LH downward to detach the 2 hooks and remove it.

  3. REMOVE SEATBACK COVER WITH PAD (for Driver Side)

    A01FIC8

    1. Disconnect the connector.

    2. A01FHLX

      Detach the hooks.

    3. A01FF3R

      Detach the wire harness clamp.

    4. A01FGXO

      Detach the 4 claws and remove the 2 front seat headrest supports.

    5. A01FFE8E01

      Detach the wire harness clamp.

    6. Remove the 2 nuts and detach the seatback cover bracket.

      Text in Illustration
      *1 Seatback Cover Bracket

    7. Remove the seatback cover with pad.

  4. REMOVE SEATBACK COVER WITH PAD (for Front Passenger Side)

    A01FHTB

    1. Disconnect the connector.

    2. A01FHR2

      Detach the hooks.

    3. A01FIPY

      Detach the 4 claws and remove the 2 front seat headrest supports.

    4. A01FD92E01

      Detach the wire harness clamp.

    5. Remove the 2 nuts and detach the 2 seatback cover brackets.

      Text in Illustration
      *1 Seatback Cover Bracket

    6. Remove the seatback cover with pad.

  5. REMOVE SEATBACK CLIMATE CONTROL BLOWER LH

    A01FGEY

    1. Disconnect the connector.

    2. Detach the 2 claws and disconnect the rear air duct LH from the lumbar support adjuster assembly LH.

    3. Remove the 2 screws.

    4. Detach the hook and remove the seatback climate control blower LH together with the rear air duct LH.

  6. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (for Driver Side)


    1. A01FIPI

      Disconnect the 2 connectors.

    2. Detach the 2 cable clamps.

    3. A01FI1O

      Remove the 2 springs and detach the 2 clips.

    4. A01FG0G

      Remove the 2 bolts.

    5. Slide the lumbar support adjuster assembly LH upward to detach the 2 hooks and remove it.

  7. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY RH (for Front Passenger Side)


    1. A01FGPB

      Disconnect the connector.

    2. Remove the 2 springs and detach the 2 clips.

    3. A01FHV3

      Remove the 2 bolts.

    4. Slide the lumbar support adjuster assembly RH upward to detach the 2 hooks and remove it.