POWER SEAT SWITCH (for Standard Seat Type) INSPECTION


  1. INSPECT POWER SEAT SWITCH ASSEMBLY (for Front Passenger Side)


    1. A01FERJE01
      Text in Illustration
      *1 Reclining Switch
      *2 Rear Lifter Switch
      *3 Front Vertical Switch
      *4 Slide Switch
      *a

      Component without harness connected

      (Front Power Seat Switch Assembly)

      for LHD:

      Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Reclining Switch
      Tester Connection Switch Condition Specified Condition
      13 (B) - 11 (RCLF) Front Below 1 Ω
      12 (RCLR) - 10 (E) Off
      11 (RCLF) - 10 (E)
      13 (B) - 12 (RCLR) Rear
      Slide Switch
      Tester Connection Switch Condition Specified Condition
      2 (SLDF) - 13 (B) Front Below 1 Ω
      5 (SLDR) - 10 (E) Off
      2 (SLDF) - 10 (E)
      5 (SLDR) - 13 (B) Rear
      Front Vertical Switch
      Tester Connection Switch Condition Specified Condition
      6 (FUP) - 13 (B) Up Below 1 Ω
      1 (FDWN) - 10 (E) Off
      6 (FUP) - 10 (E)
      1 (FDWN) - 13 (B) Down
      Rear Lifter Switch
      Tester Connection Switch Condition Specified Condition
      4 (LUP) - 13 (B) Up Below 1 Ω
      3 (LDWN) - 10 (E) Off
      4 (LUP) - 10 (E)
      3 (LDWN) - 13 (B) Down

      If the result is not as specified, replace the power seat switch assembly.

    2. for LHD:

      Measure the resistance according to the value in the table below.

      Front Lumbar Power Seat Switch Junction Circuit
      Tester Connection Specified Condition
      14 (B1) - 13 (B) Below 1 Ω
      10 (E) - 9 (E1)

      If the result is not as specified, replace the power seat switch assembly.

    3. A01FEY6E01
      Text in Illustration
      *1 Reclining Switch
      *2 Rear Lifter Switch
      *3 Front Vertical Switch
      *4 Slide Switch
      *a

      Component without harness connected

      (Power Seat Switch Assembly)

      for RHD:

      Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Reclining Switch
      Tester Connection Switch Condition Specified Condition
      8 (B) - 10 (RCLF) Front Below 1 Ω
      9 (RCLR) - 11 (E) Off
      10 (RCLF) - 11 (E)
      8 (B) - 9 (RCLR) Rear
      Slide Switch
      Tester Connection Switch Condition Specified Condition
      5 (SLDF) - 8 (B) Front Below 1 Ω
      2 (SLDR) - 11 (E) Off
      5 (SLDF) - 11 (E)
      2 (SLDR) - 8 (B) Rear
      Front Vertical Switch
      Tester Connection Switch Condition Specified Condition
      1 (FUP) - 8 (B) Up Below 1 Ω
      6 (FDWN) - 11 (E) Off
      1 (FUP) - 11 (E)
      6 (FDWN) - 8 (B) Down
      Rear Lifter Switch
      Tester Connection Switch Condition Specified Condition
      3 (LUP) - 8 (B) Up Below 1 Ω
      4 (LDWN) - 11 (E) Off
      3 (LUP) - 11 (E)
      4 (LDWN) - 8 (B) Down

      If the result is not as specified, replace the power seat switch assembly.

    4. for RHD:

      Measure the resistance according to the value in the table below.

      Front Lumbar Power Seat Switch Junction Circuit
      Tester Connection Specified Condition
      7 (B1) - 8 (B) Below 1 Ω
      11 (E) - 12 (E1)

      If the result is not as specified, replace the power seat switch assembly.