POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION

INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

1. Apply MP grease to the sliding and rotating areas of the rear door window regulator.

2. Temporarily install the temporary bolt to the rear door window regulator.

3. 

   Text in Illustration

   *1	Temporary Bolt

   Install the rear door window regulator with the 3 bolts, and then tighten the temporary bolt.

   Torque:

   11 N*m  { 112 kgf*cm, 8 ft.*lbf }

   Note

   Be careful not to drop the rear door window regulator as it may become damaged.

4. Connect the connector.

INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

INSTALL REAR DOOR QUARTER WINDOW GLASS LH

1. Install the rear door quarter window glass.

INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

1. Align the rear door glass run with the rear door rear lower window frame.

2. Insert the rear door rear lower window frame together with the rear door glass run into the front door panel.

3. Partially install the screw and 2 bolts.

4. Install the upper side of the rear door glass run.

INSTALL REAR DOOR GLASS RUN LH

1. Finish installing the rear door glass run.

INSTALL REAR NO. 2 SPEAKER ASSEMBLY

1. Finish installing the rear door glass run.

INSTALL REAR DOOR SERVICE HOLE COVER LH

1. Apply new butyl tape to the rear door panel.

2. 

   Text in Illustration

   *a	Reference Point

   Pass the rear door inside locking cable and rear door lock remote control cable through a new rear door service hole cover, and then attach the rear door service hole cover using the reference points on the rear door panel.

   Note

   
   

   • Securely install the rear door service hole cover to prevent wrinkles and air bubbles.

   • There should be no wrinkles or folds after installing the rear door service hole cover.

   • After installing the rear door service hole cover, check the seal quality.

INSTALL REAR DOOR ARMREST SET BRACKET LH

1. Install the rear door armrest set bracket with the 2 screws.

INSTALL REAR DOOR FRAME GARNISH LH

1. Attach the 2 clips to install the rear door frame garnish.

INSTALL REAR SIDE CURTAIN ASSEMBLY LH (w/ Rear Sunshade)

1. Attach the 2 clips and 4 claws to install the rear side curtain.

INSTALL REAR DOOR TRIM COVER LH

1. Attach the 6 clips to install the rear door trim cover.

INSTALL REAR DOOR NO. 1 STIFFENER CUSHION

1. Install the rear door No. 1 stiffener cushion.

INSTALL REAR DOOR GLASS INNER WEATHERSTRIP LH

1. Install the rear door inner glass weatherstrip.

INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

1. Connect the rear door lock remote control cable and rear door inside locking cable.

2. Connect each connector.

3. 

   Text in Illustration

   *1	Reference Boss

   Attach the 3 claws to install the rear door trim board to the rear door inner glass weatherstrip.

4. Attach the reference boss in the direction indicated by the arrow in the illustration.

5. Attach the 8 clips to install the rear door trim board.

6. Install the 3 screws.

INSTALL REAR DOOR HOLE COVER

1. Install the rear door hole cover.

INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

1. Connect the connector.

2. Attach the 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

1. Attach the 3 claws to install the rear door inside handle bezel plug.