AUTOMATIC TRANSMISSION UNIT DISASSEMBLY


  1. REMOVE TRANSMISSION CASE COVER (w/ Case Cover)


    1. A01FEC9

      Remove the 2 bolts and the transmission case cover from the automatic transmission case sub-assembly.

  2. REMOVE REFILL PLUG


    1. Remove the refill plug.

    2. Remove the O-ring from the refill plug.

  3. REMOVE TRANSMISSION CONTROL SHAFT LEVER RH


    1. A01FFRQ

      Remove the nut, spring washer and the transmission control shaft lever RH from the park/neutral position switch assembly.

  4. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. A01FIMA

      Using a screwdriver, bend the tabs of the lock washer.

    2. Remove the nut and the lock washer.

    3. Remove the bolt and the park/neutral position switch assembly from the automatic transmission case sub-assembly.

      Tech Tips

      Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.

  5. REMOVE TRANSMISSION OIL COOLER


    1. A01FHMP

      Remove the 3 bolts and the transmission oil cooler from the automatic transmission case sub-assembly.

    2. A01FDC1E03
      Text in Illustration
      *1 O-ring

      Remove the 2 O-rings from the transmission oil cooler.

  6. REMOVE WIRE HARNESS CLAMP BRACKET


    1. A01FH31

      Remove the bolt and the wire harness clamp bracket from the automatic transmission case sub-assembly.

  7. REMOVE TRANSMISSION REVOLUTION SENSOR


    1. A01FGLZ

      Remove the 2 bolts and the 2 transmission revolution sensors from the automatic transmission case sub-assembly.

    2. Remove the 2 O-rings from the 2 transmission revolution sensors.

  8. REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE


    1. A01FINL

      Remove the 2 bolts and the automatic transmission breather tube from the automatic transmission case sub-assembly.

  9. REMOVE AUTOMATIC TRANSMISSION CASE PLUG


    1. A01FEVK

      Remove the 5 automatic transmission case plugs from the automatic transmission case sub-assembly.

    2. Remove the 5 O-rings from the 5 automatic transmission case plugs.

    3. A01FHWV

      Using T55 "TORX" socket wrench , remove the automatic transmission case plug from the automatic transmission case sub-assembly.

    4. Remove the O-ring from the automatic transmission case plug.

  10. REMOVE AUTOMATIC TRANSMISSION HOUSING


    1. A01FIBU

      Remove the 10 bolts and the automatic transmission housing from the automatic transmission case sub-assembly.

  11. REMOVE EXTENSION HOUSING DUST DEFLECTOR


    1. A01FDUG

      Using a brass bar and a hammer, tap out the extension housing dust deflector from the extension housing sub-assembly.

      Note

      Be careful not to damage the extension housing sub-assembly.

  12. REMOVE EXTENSION HOUSING SUB-ASSEMBLY


    1. A01FJ0P

      Remove the 6 bolts.

    2. A01FDALE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the extension housing sub-assembly from the automatic transmission case sub-assembly.

      Note

      Do not pry the surface where the extension housing sub-assembly contacts the automatic transmission case sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  13. REMOVE TRANSMISSION CASE ADAPTER RADIAL BALL BEARING


    1. A01FITL

      Using snap ring pliers, remove the snap ring from the extension housing sub-assembly.

    2. Remove the transmission case adapter radial ball bearing from the extension housing sub-assembly.

  14. REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL


    1. A01FGCEE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, pry out the automatic transmission extension housing oil seal from the extension housing sub-assembly.

      Note

      Be careful not to damage the extension housing sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  15. REMOVE OUTPUT SHAFT THRUST BEARING


    1. A01FFB8

      Using a snap ring expander, remove the snap ring from the output shaft of the rear planetary gear assembly.

    2. Remove the rear output shaft thrust bearing race, output shaft thrust bearing and the output shaft thrust bearing race.

  16. SECURE AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY


    1. A01FF3NE01

      Install the automatic transmission case sub-assembly to an overhaul attachment.

  17. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

    Note

    Do not turn the transmission over as this will contaminate the valve body with foreign matter located at the bottom of the oil pan.


    1. Using a socket hexagon wrench 5 mm, remove the overflow plug and gasket.

    2. Remove the drain plug and gasket.

    3. A01FIBJ

      Remove the 20 bolts, automatic transmission oil pan sub-assembly and the automatic transmission oil pan gasket.

    4. A01FILGE04
      Text in Illustration
      *1 Transmission Oil Cleaner Magnet

      Remove the 3 transmission oil cleaner magnets from the automatic transmission oil pan sub-assembly.

    5. Examine the particles in the automatic transmission oil pan sub-assembly.


      1. Collect any steel chips with the removed transmission oil cleaner magnets. Carefully inspect the foreign matter and particles in the automatic transmission oil pan sub-assembly and on the transmission oil cleaner magnets to anticipate the type of wear you will find in the automatic transmission assembly.

        Steel (magnetic): bearing, gear and clutch plate wear

        Brass (non-magnetic): bush wear

  18. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    1. Turn over the automatic transmission case sub-assembly.

    2. A01FFKL

      Remove the 4 bolts and the valve body oil strainer assembly from the transmission valve body assembly.

    3. A01FFORE01
      Text in Illustration
      *1 O-ring

      Remove the O-ring from the valve body oil strainer assembly.

  19. REMOVE TRANSMISSION WIRE


    1. A01FGWO

      Remove the bolt and the temperature sensor clamp, and separate the ATF temperature sensor.

    2. A01FGQT

      Remove the 2 bolts and the 2 valve body wire harness clamps.

    3. A01FD9Y

      Disconnect the 9 solenoid valve connectors.

    4. A01FHSTE01

      Remove the bolt and pull out the transmission wire.

    5. A01FGH6E05
      Text in Illustration
      *1 O-ring

      Remove the O-ring from the transmission wire.

  20. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    1. A01FH6L

      Remove the bolt, detent spring cover and the detent spring from the transmission valve body assembly.

    2. A01FGPF

      Remove the 19 bolts and the transmission valve body assembly from the automatic transmission case sub-assembly.

    3. A01FIM3E07
      Text in Illustration
      *1 Manual Valve Connecting Rod Sub-assembly
      *2 Manual Valve Lever Sub-assembly

      Disconnect the manual valve connecting rod sub-assembly from the manual valve lever sub-assembly.

  21. REMOVE TRANSMISSION CASE GASKET


    1. A01FEW2E03

      Remove the 3 transmission case gaskets from the automatic transmission case sub-assembly.

  22. REMOVE BRAKE DRUM GASKET


    1. A01FJ52E01

      Remove the 3 brake drum gaskets from the automatic transmission case sub-assembly.

  23. REMOVE CHECK BALL BODY


    1. A01FIFPE13
      Text in Illustration
      *1 Check Ball Body
      *2 Compression Spring

      Remove the check ball body and the compression spring from the automatic transmission case sub-assembly.

  24. REMOVE C-2 ACCUMULATOR PISTON


    1. A01FI9NE01

      While blowing compressed air into the oil hole, remove the C-2 accumulator piston and the spring from the automatic transmission case sub-assembly.

      Note

      Take care as the C-3 and B-3 accumulator pistons may jump out.

    2. Remove the 2 O-rings from the C-2 accumulator piston.

    3. A01FDBB

      Using a screwdriver, remove the snap ring and the spring sub-assembly from the C-2 accumulator piston.

      Note

      Be careful not to damage the C-2 accumulator piston.

      Tech Tips

      Tape the screwdriver tip before use.

  25. REMOVE B-3 ACCUMULATOR PISTON


    1. While blowing compressed air into the oil hole, remove the B-3 accumulator piston and the spring from the automatic transmission case sub-assembly.

      Note

      Take care as the C-3 accumulator piston may jump out.

    2. Remove the 2 O-rings from the B-3 accumulator piston.

    3. A01FDBB

      Using a screwdriver, remove the snap ring and the spring sub-assembly from the B-3 accumulator piston.

      Note

      Be careful not to damage the B-3 accumulator piston.

      Tech Tips

      Tape the screwdriver tip before use.

  26. REMOVE C-3 ACCUMULATOR PISTON


    1. A01FI2GE01

      While blowing compressed air into the oil hole, remove the C-3 accumulator piston and the 2 springs from the automatic transmission case sub-assembly.

    2. Remove the 2 O-rings from the C-3 accumulator piston.

    3. A01FDBB

      Using a screwdriver, remove the snap ring and the spring sub-assembly from the C-3 accumulator piston.

      Note

      Be careful not to damage the C-3 accumulator piston.

      Tech Tips

      Tape the screwdriver tip before use.

  27. REMOVE B-1 ACCUMULATOR VALVE


    1. A01FGNY

      Remove the B-1 accumulator valve and the spring from the automatic transmission case sub-assembly.

  28. REMOVE PARKING LOCK PAWL BRACKET


    1. A01FI4RE01

      Remove the 3 bolts and the parking lock pawl bracket from the automatic transmission case sub-assembly.

  29. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    1. A01FETVE01

      Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.

  30. REMOVE PARKING LOCK PAWL SHAFT


    1. A01FECTE04
      Text in Illustration
      *1 Parking Lock Pawl
      *2 E-ring
      *3 Parking Lock Pawl Shaft
      *4 Torsion Spring

      Pull out the parking lock pawl shaft from the front side, and remove the parking lock pawl and the torsion spring.

    2. Remove the E-ring from the parking lock pawl shaft.

  31. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


    1. A01FHLHE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver and a hammer, cut off the spacer and remove it from the manual valve lever shaft.

      Note

      Be careful not to damage the manual valve lever shaft.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01FII9

      Using a pin punch 3 mm and a hammer, drive out the spring pin.

      Tech Tips

      Slowly drive out the spring pin so that it does not fall into the automatic transmission case sub-assembly.

    3. Pull the manual valve lever shaft out through the case and remove the manual valve lever sub-assembly.

  32. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    1. A01FG94E04
      Text in Illustration
      *1 Protective Tape
      *a RH Side
      *b LH Side

      Using a screwdriver, pry out the 2 manual valve lever shaft oil seals from the automatic transmission case sub-assembly.

      Note

      Be careful not to damage the automatic transmission case sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  33. REMOVE OIL PUMP ASSEMBLY


    1. A01FDEE

      Remove the 9 bolts.

    2. A01FFW0E04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, pull out the oil pump assembly from the automatic transmission case sub-assembly.

      Note

      Be careful not to damage the oil pump assembly or automatic transmission case sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01FDV8E04
      Text in Illustration
      *1 No. 1 Thrust Bearing Race
      *2 Oil Pump Assembly
      *3 O-ring

      Remove the No. 1 thrust bearing race from the oil pump assembly.

    4. Remove the O-ring from the oil pump assembly.

  34. REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    1. A01FIV4E01

      Remove the clutch drum and input shaft assembly from the automatic transmission case sub-assembly.

    2. A01FGGQE09
      Text in Illustration
      *1 Thrust Needle Roller Bearing
      *2 Input Shaft Front Thrust Bearing Race
      *3 Input Shaft Front Thrust Needle Roller Bearing
      *4 Clutch Drum Thrust Washer

      Remove the clutch drum thrust washer, thrust needle roller bearing, input shaft front thrust bearing race and the input shaft front thrust needle roller bearing from the clutch drum and input shaft assembly.

  35. REMOVE NO. 2 ONE-WAY CLUTCH ASSEMBLY


    1. A01FFV4E06
      Text in Illustration
      *1 No. 2 One-way Clutch Assembly
      *2 Input Shaft Clutch Drum Thrust Washer

      Remove the No. 2 one-way clutch assembly and the input shaft clutch drum thrust washer from the clutch drum and input shaft assembly.

  36. SUPPORT CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    1. A01FE2IE06
      Text in Illustration
      *1 Torque Converter Assembly
      *2 Oil Pump Assembly

      Place the oil pump assembly onto the torque converter assembly, and then place the clutch drum and input shaft assembly onto the oil pump assembly.

  37. REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY


    1. A01FE4QE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the snap ring from the reverse clutch piston sub-assembly.

      Note

      Be careful not to damage the reverse clutch piston sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01FIXHE01

      Remove the reverse clutch hub sub-assembly from the reverse clutch drum sub-assembly.

  38. REMOVE REVERSE CLUTCH REACTION SLEEVE


    1. A01FIY9E01

      Remove the reverse clutch reaction sleeve from the reverse clutch hub sub-assembly.

  39. REMOVE NO. 3 CLUTCH DISC (REAR CLUTCH DISC)


    1. Remove the clutch cushion plate, reverse clutch flange, 4 No. 3 clutch discs and the 3 No. 3 clutch plates from the reverse clutch hub sub-assembly.

  40. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY


    1. A01FES1E03
      Text in Illustration
      *1 Forward Clutch Hub Sub-assembly
      *2 No. 3 Clutch Hub Thrust Washer

      Remove the forward clutch hub sub-assembly and the No. 3 clutch hub thrust washer from the reverse clutch drum sub-assembly.

    2. A01FG22E10
      Text in Illustration
      *1 Thrust Needle Roller Bearing
      *2 No. 2 Thrust Bearing Race

      Remove the 2 thrust needle roller bearings and the No. 2 thrust bearing race from the forward clutch hub sub-assembly.

  41. REMOVE COAST CLUTCH HUB SUB-ASSEMBLY


    1. A01FGUSE02

      Remove the coast clutch hub sub-assembly from the reverse clutch drum sub-assembly.

  42. REMOVE NO. 4 ONE-WAY CLUTCH ASSEMBLY


    1. A01FGEQE04
      Text in Illustration
      *1 Coast Clutch Hub Sub-assembly
      *2 No. 2 Clutch Hub Thrust Washer
      *3 No. 4 One-way Clutch Assembly

      Remove the No. 4 one-way clutch assembly and the No. 2 clutch hub thrust washer from the coast clutch hub sub-assembly.

  43. REMOVE NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)


    1. A01FE67E03
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the snap ring.

      Note

      Be careful not to damage the input shaft.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the forward clutch flange, 4 No. 1 clutch discs, 4 No. 1 clutch plates and the clutch cushion plate from the input shaft.

  44. REMOVE NO. 4 CLUTCH DISC (COAST CLUTCH DISC)


    1. A01FEQJE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the snap ring.

      Note

      Be careful not to damage the forward clutch piston sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the coast clutch flange, 4 No. 4 clutch discs and the 4 No. 4 clutch plates from the forward clutch piston sub-assembly.

  45. REMOVE INPUT SHAFT


    1. A01FDN6E06
      Text in Illustration
      *1 Thrust Needle Roller Bearing
      *2 Input Shaft Rear Thrust Bearing Race

      Remove the thrust needle roller bearing and the input shaft rear thrust bearing race from the input shaft.

    2. A01FI3OE01

      Remove the input shaft from the reverse clutch drum sub-assembly.

  46. REMOVE CLUTCH DRUM OIL SEAL RING


    1. A01FDSOE01

      Remove the 4 clutch drum oil seal rings from the input shaft.

  47. REMOVE NO. 1 CLUTCH BALANCER


    1. A01FFA2E01

      Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.

      SST
      09387-00110

    2. Using SST, remove the snap ring.

      SST
      09350-30020   ( 09350-07070 )
    3. A01FE91E01
      Text in Illustration
      *1 No. 1 Clutch Balancer
      *2 Forward Clutch Return Spring Sub-assembly

      Remove the No. 1 clutch balancer and the forward clutch return spring sub-assembly from the input shaft.

    4. A01FII0E02
      Text in Illustration
      *1 D-ring

      Remove the D-ring from the No. 1 clutch balancer.

  48. REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY


    1. A01FG06E01

      Hold the forward clutch piston sub-assembly and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the input shaft to remove the forward clutch piston sub-assembly.

    2. A01FGT1E03
      Text in Illustration
      *1 Coast Clutch Piston
      *2 Forward Clutch Piston Sub-assembly

      Remove the coast clutch piston from the forward clutch piston sub-assembly.

    3. A01FH9QE01
      Text in Illustration
      *1 O-ring

      Remove the O-ring from the input shaft.

  49. REMOVE REVERSE CLUTCH FLANGE


    1. A01FEZDE01

      Remove the reverse clutch flange from the reverse clutch drum sub-assembly.

  50. REMOVE NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)


    1. A01FEBGE03
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the 2 snap rings from the reverse clutch drum sub-assembly.

      Note

      Be careful not to damage the reverse clutch drum sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the direct clutch flange, 5 No. 2 clutch discs and the 5 No. 2 clutch plates from the reverse clutch drum sub-assembly.

  51. REMOVE NO. 3 CLUTCH BALANCER


    1. A01FFNNE04

      Place SST on the No. 3 clutch balancer, and compress the reverse clutch return spring sub-assembly with a press.

      SST
      09387-00070

    2. Using SST, remove the snap ring.

      SST
      09350-30020   ( 09350-07070 )

    3. Remove the No. 3 clutch balancer.

  52. REMOVE REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


    1. A01FHYME05
      Text in Illustration
      *1 Reverse Clutch Return Spring Sub-assembly
      *2 O-ring
      *3 Reverse Clutch Piston Sub-assembly

      Remove the reverse clutch return spring sub-assembly and O-ring from the reverse clutch piston sub-assembly.

  53. REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY


    1. A01FFWQE02
      Text in Illustration
      *1 Reverse Clutch Piston Sub-assembly
      *2 Reverse Clutch Drum Sub-assembly

      Remove the reverse clutch piston sub-assembly from the reverse clutch drum sub-assembly.

    2. A01FDTIE03
      Text in Illustration
      *1 O-ring

      Remove the O-ring from the reverse clutch piston sub-assembly.

    3. A01FDE9E03
      Text in Illustration
      *1 O-ring

      Remove the O-ring from the reverse clutch drum sub-assembly.

  54. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY


    1. A01FGUUE01

      Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.

      SST
      09320-89010

    2. Using SST, remove the snap ring.

      SST
      09350-30020   ( 09350-07070 )
    3. A01FHZVE01
      Text in Illustration
      *1 No. 2 Clutch Balancer
      *2 O-ring
      *3 Direct Clutch Return Spring Sub-assembly

      Remove the No. 2 clutch balancer and the direct clutch return spring sub-assembly.

    4. Remove the O-ring from the No. 2 clutch balancer.

    5. A01FDOZE03
      Text in Illustration
      *1 Protective Tape

      Using 2 screwdrivers, remove the direct clutch piston sub-assembly from the reverse clutch drum sub-assembly.

      Note

      Be careful not to damage the direct clutch piston sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    6. A01FIIEE03
      Text in Illustration
      *1 O-ring

      Remove the 2 O-rings from the direct clutch piston sub-assembly.

  55. REMOVE NO. 3 BRAKE DISC (2ND BRAKE DISC SET)


    1. A01FDM9E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.

      Note

      Be careful not to damage the automatic transmission case sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the No. 3 brake flange, 3 No. 3 brake discs and the 3 No. 3 brake plates from the automatic transmission case sub-assembly.

  56. REMOVE 2ND BRAKE CYLINDER


    1. A01FIK2E10

      Using SST, remove the snap ring from the automatic transmission case sub-assembly.

      SST
      09350-30020   ( 09350-07060 )
    2. A01FFGV

      Remove the 2nd brake cylinder from the automatic transmission case sub-assembly.

  57. REMOVE 2ND BRAKE PISTON


    1. A01FFIZ

      Using a screwdriver, remove the snap ring and the No. 3 brake piston return spring sub-assembly from the 2nd brake cylinder.

      Note

      Be careful not to damage the 2nd brake cylinder.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01FEP0E01

      Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston.

    3. A01FHA5E14
      Text in Illustration
      *1 O-ring

      Remove the 2 O-rings from the 2nd brake piston.

  58. REMOVE ONE-WAY CLUTCH ASSEMBLY


    1. A01FJ44E04
      Text in Illustration
      *1 One-way Clutch Assembly
      *2 No. 1 Planetary Carrier Thrust Washer

      Remove the one-way clutch assembly and the No. 1 planetary carrier thrust washer from the automatic transmission case sub-assembly.

  59. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    1. A01FILKE04
      Text in Illustration
      *1 One-way Clutch Inner Race Sub-assembly
      *2 Front Planetary Gear Assembly

      Remove the front planetary gear assembly and the one-way clutch inner race sub-assembly from the automatic transmission case sub-assembly.

    2. A01FIFVE17
      Text in Illustration
      *1 Front Planetary Flange Rear Thrust Bearing Race
      *2 Front Planetary Flange Thrust Needle Roller Bearing
      *3 No. 2 Planetary Carrier Thrust Washer

      Remove the front planetary flange rear thrust bearing race, front planetary flange thrust needle roller bearing and the No. 2 planetary carrier thrust washer from the automatic transmission case sub-assembly.

  60. REMOVE FRONT PLANETARY RING GEAR


    1. A01FE28

      Remove the front planetary ring gear from the automatic transmission case sub-assembly.

  61. REMOVE CENTER PLANETARY RING GEAR


    1. A01FGEZE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the snap ring.

      Note

      Be careful not to damage the front planetary ring gear.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the center planetary ring gear from the front planetary ring gear.

    3. A01FIW7E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the snap ring.

      Note

      Be careful not to damage the center planetary ring gear.

      Tech Tips

      Tape the screwdriver tip before use.

    4. Remove the front planetary ring gear flange sub-assembly from the center planetary ring gear.

  62. REMOVE NO. 1 BRAKE DISC


    1. Remove the No. 1 brake flange, 3 No. 1 brake discs and the 3 No. 1 brake plates from the automatic transmission case sub-assembly.

  63. REMOVE BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    1. A01FIYME02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.

      Note

      Be careful not to damage the automatic transmission case sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01FHGBE05
      Text in Illustration
      *1 Brake Piston Return Spring Sub-assembly
      *2 No. 1 Brake Cylinder

      Remove the brake piston return spring sub-assembly and the No. 1 brake cylinder from the automatic transmission case sub-assembly.

  64. REMOVE NO. 1 BRAKE PISTON


    1. A01FFJHE01

      Hold the No. 1 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the No. 1 brake cylinder to remove the No. 1 brake piston.

      Tech Tips

      If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

    2. Remove the 2 O-rings from the No. 1 brake piston.

  65. REMOVE NO. 2 BRAKE DISC


    1. A01FH4WE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the snap ring from the automatic transmission case sub-assembly.

      Note

      Be careful not to damage the automatic transmission case sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the 2 No. 2 brake flanges, 4 No. 2 brake discs, 3 No. 2 brake plates and the No. 2 brake piston return spring sub-assembly from the automatic transmission case sub-assembly.

  66. REMOVE NO. 2 BRAKE PISTON


    1. A01FFX5E01

      Hold the No. 2 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the No. 2 brake piston and the No. 2 brake cylinder.

      Tech Tips

      If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

    2. Remove the No. 2 brake piston from the No. 2 brake cylinder.

    3. Remove the 2 O-rings from the No. 2 brake piston.

  67. REMOVE CENTER PLANETARY GEAR ASSEMBLY


    1. A01FIALE01
      Text in Illustration
      *1 Thrust Needle Roller Bearing
      *2 No. 4 Thrust Bearing Race
      *3 Center Planetary Gear Assembly
      *4 Planetary Sun Gear

      Remove the center planetary gear assembly, planetary sun gear, thrust needle roller bearing and the No. 4 thrust bearing race from the automatic transmission case sub-assembly.

  68. REMOVE INTERMEDIATE SHAFT


    1. A01FIW6E04

      Using SST, remove the snap ring from the automatic transmission case sub-assembly.

      SST
      09350-30020   ( 09350-07060 )
    2. A01FDHRE01

      Remove the intermediate shaft together with the No. 3 one-way clutch assembly from the automatic transmission case sub-assembly.

  69. REMOVE NO. 3 ONE-WAY CLUTCH ASSEMBLY


    1. A01FDFFE03
      Text in Illustration
      *1 No. 3 One-way Clutch Assembly
      *2 One-way Clutch Inner Race

      Remove the No. 3 one-way clutch assembly and the one-way clutch inner race from the intermediate shaft.

  70. REMOVE REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY


    1. A01FIXWE07
      Text in Illustration
      *1 Rear Planetary Ring Gear Flange Sub-assembly
      *2 No. 7 Thrust Bearing Race
      *3 Thrust Needle Roller Bearing
      *4 No. 8 Thrust Bearing Race

      Remove the rear planetary ring gear flange sub-assembly, No. 7 thrust bearing race, thrust needle roller bearing and the No. 8 thrust bearing race from the intermediate shaft.

  71. REMOVE BRAKE PLATE STOPPER SPRING


    1. A01FH2NE01

      Remove the brake plate stopper spring from the automatic transmission case sub-assembly.

  72. REMOVE NO. 4 BRAKE DISC


    1. Remove the 2 No. 4 brake flanges, 5 No. 4 brake discs and the 4 No. 4 brake plates from the automatic transmission case sub-assembly.

  73. REMOVE REAR PLANETARY GEAR ASSEMBLY


    1. A01FH9Z

      Remove the rear planetary gear assembly from the automatic transmission case sub-assembly.

    2. A01FIYVE06
      Text in Illustration
      *1 Thrust Bearing Race
      *2 Thrust Needle Roller Bearing
      *3 No. 9 Thrust Bearing Race

      Remove the thrust bearing race, thrust needle roller bearing and the No. 9 thrust bearing race from the rear planetary gear assembly.

    3. A01FE5GE01

      Remove the thrust needle roller bearing from the automatic transmission case sub-assembly.

  74. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    1. A01FGO5E03
      Text in Illustration
      *1 Snap Ring

      Place SST on the 1st and reverse brake return spring sub-assembly and compress the 1st and reverse brake return spring sub-assembly.

      SST
      09350-30020   ( 09350-07050 )

    2. Using SST, remove the snap ring and the 1st and reverse brake return spring sub-assembly.

      SST
      09350-30020   ( 09350-07070 )

  75. REMOVE BRAKE APPLY TUBE


    1. A01FG7U

      Remove the brake apply tube from the automatic transmission case sub-assembly.

  76. REMOVE 1ST AND REVERSE BRAKE PISTON


    1. A01FG6Y

      Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.

      Tech Tips

      If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

    2. Remove the O-ring from the 1st and reverse brake piston.

  77. REMOVE BRAKE REACTION SLEEVE


    1. A01FIGGE01

      Using SST, remove the brake reaction sleeve from the automatic transmission case sub-assembly.

      SST
      09350-30020   ( 09350-07080 )

    2. Remove the 2 O-rings from the brake reaction sleeve.

  78. REMOVE NO. 4 BRAKE PISTON


    1. A01FI6LE01

      Using SST, remove the No. 4 brake piston from the automatic transmission case sub-assembly.

      SST
      09350-30020   ( 09350-07090 )

    2. Remove the 2 O-rings from the No. 4 brake piston.