COOLING FAN MOTOR REMOVAL


  1. REMOVE ENGINE ROOM SIDE COVER


    1. A01FGMK

      Remove the 4 clips and engine room side cover.

  2. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A01FGF0

      Remove the 7 clips and cool air intake duct seal.

  3. REMOVE NO. 1 AIR CLEANER INLET


    1. A01FHG8

      Remove the bolt and No. 1 air cleaner inlet.

  4. REMOVE V-BANK COVER SUB-ASSEMBLY


    1. A01FFEFE01

      Place both hands on the sides of the cover as shown in the illustration, lift the cover to detach the 2 clips near the front in the order shown in the illustration, and then lift the cover further to detach the rear clip and remove the cover.

      Text in Illustration
      A01FE8R Areas to place hands when lifting cover

      Note

      If the cover is lifted rearward or forward and to the right or left at the same time, the cover maybe damaged.

  5. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE


    1. A01FEMK

      Disconnect the mass air flow meter connector.

    2. Disconnect the clamp from the air cleaner.

    3. A01FDGM

      Disconnect the VSV hose.

    4. A01FDVX

      for RHD:

      Disconnect the union to check valve hose.

    5. A01FF3K

      Disconnect the 4 clamps.

    6. Remove the hose clamp and air cleaner cap with air cleaner hose.

  6. DRAIN ENGINE COOLANT


    1. Loosen the radiator drain cock plug and drain the coolant.

      A01FFY9E01
      Text in Illustration
      *1 Radiator Cap *2 Radiator Drain Cock Plug
      *3 Cylinder Block Drain Cock Plug *4 Radiator Reservoir Tank

      CAUTION:

      Do not remove the radiator cap, cylinder block drain cock plugs and radiator drain cock plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

      Tech Tips

      Collect the coolant in a container and dispose of it according to the local regulations.

    2. Remove the radiator cap.

    3. Loosen the 2 cylinder block drain cock plugs.

  7. REMOVE NO. 1 RADIATOR HOSE


    1. A01FEGM

      Remove the No. 1 radiator hose.

  8. REMOVE RADIATOR RESERVOIR TANK


    1. A01FJ49E01

      Remove the reservoir tank hose from the water inlet assembly.

    2. Disconnect the wire harness clamp from the radiator reservoir tank.

    3. Remove the 2 bolts and radiator reservoir tank.

  9. DISCONNECT NO. 2 ENGINE ROOM WIRE


    1. A01FJ23E01

      Disconnect the 6 wire harness clamps, connector and No. 2 engine room wire.

  10. REMOVE ENGINE ROOM ECU OUTLET DUCT


    1. A01FEYME06

      Remove the engine room ECU outlet duct from the engine room ECU box.

  11. DISCONNECT NO. 2 OIL COOLER OUTLET HOSE (w/ Transmission Oil Cooler)


    1. A01FDGL

      Detach the flexible hose clamp.

  12. REMOVE FAN SHROUD


    1. A01FEFK

      Remove the 2 bolts and detach the claw on the upper part of the fan shroud.

    2. Detach the 2 claws on the lower part of the fan shroud and remove the fan shroud.

  13. REMOVE COOLING FAN ECU


    1. A01FDJQ

      Disconnect the 3 clamps and 2 connectors.

    2. Remove the 2 screws and cooling fan ECU.

  14. REMOVE FAN


    1. A01FITV

      Remove the nut and fan.

  15. REMOVE NO. 2 FAN


    1. A01FEX9

      Remove the nut and No. 2 fan.

  16. REMOVE COOLING FAN MOTOR


    1. A01FFNU

      Remove the 3 screws and cooling fan motor.

  17. REMOVE NO. 2 COOLING FAN MOTOR


    1. A01FE80

      Remove the 3 screws and No. 2 cooling fan motor.