CYLINDER HEAD REASSEMBLY

Tech Tips

w/ Canister Pump Module:

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly or cylinder head LH Click here.


  1. INSTALL SPARK PLUG TUBE

    Note

    When using a new cylinder head, the spark plug tubes must be replaced.


    1. A01FDNTE12
      Text in Illustration
      *1 Standard Application Width
      *a 9.0 to 15.0 mm (0.354 to 0.591 in.)

      Apply adhesive onto the shaded area of a new spark plug tube.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
      Standard application width
      1.0 to 3.0 mm (0.0394 to 0.118 in.)

      Note


      • Install the spark plug tube within 3 minutes after applying adhesive.

      • Be careful not to deform the spark plug tube.

      • Be careful not to expose the seal to coolant for at least 1 hour after installing it.

    2. A01FHRFE15
      Text in Illustration
      *1 Standard Protrusion Height
      *2 Cylinder Head Casting Surface

      Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

      Standard protrusion height
      72.9 mm (2.87 in.)

      Note

      To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.

  2. INSTALL NO. 1 STRAIGHT SCREW PLUG


    1. Using a 10 mm hexagon wrench, install 4 new gaskets and the 4 No. 1 straight screw plugs.

      Torque:
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }

  3. INSTALL NO. 2 STRAIGHT SCREW PLUG


    1. Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 No. 2 straight screw plugs.

      Torque:
      80 N*m  { 816 kgf*cm, 59 ft.*lbf }

  4. INSTALL UNION


    1. Apply adhesive to the union of the cylinder head.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    2. Using a union nut wrench (12 mm), install the union to the cylinder head as shown in the illustration.

      A01FE1EE08
      Text in Illustration
      *A Bank 1 *B Bank 2
      Torque:
      15 N*m  { 150 kgf*cm, 11 ft.*lbf }

  5. INSTALL STUD BOLT

    Note

    If the stud bolt is deformed or the threads are damaged, replace it.


    1. Using E6 and E8 "TORX" socket wrenches, install the stud bolts.

      A01FDYUE01
      Text in Illustration
      *a Rear Side LH *b Intake Side RH
      *c Rear Side RH *d Exhaust Side RH
      *e Exhaust Side LH *f Intake Side LH
      Torque:
      Bolt A, B
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      Bolt C
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

  6. INSTALL VALVE SPRING SEAT


    1. Install the valve spring seats to the cylinder head.

  7. INSTALL VALVE STEM OIL SEAL


    1. A01FDCRE15
      Text in Illustration
      *1 Gray
      *2 Black
      *a Intake Side
      *b Exhaust Side

      Apply a light coat of engine oil to new valve stem oil seals.

      Note

      Pay attention when installing the intake and exhaust valve stem oil seals. For example, installing the intake valve stem oil seal into the exhaust side or installing the exhaust valve stem oil seal to the intake side can cause installation problems later.

      Tech Tips

      The intake valve oil seals are gray and the exhaust valve oil seals are black.

    2. A01FHOQE05
      Text in Illustration
      *a CORRECT
      *b INCORRECT

      Using SST, push in the oil seals.

      SST
      09201-41020

      Note

      Failure to use SST will cause the seal to be damaged or improperly seated.

  8. INSTALL EXHAUST VALVE


    1. A01FDK5E35
      Text in Illustration
      *a 40 mm (1.57 in.) or more

      Apply a sufficient coat of engine oil to the tip area of the exhaust valve shown in the illustration.

    2. Install the exhaust valve, inner compression spring and valve spring retainer to the cylinder head.

      Note

      Install the same parts in the same combination to their original locations.

    3. A01FDDPE01

      Using SST, compress the inner compression spring and install the 2 valve spring retainer locks.

      SST
      09202-70020   ( 09202-00010, 09202-01010, 09202-01020 )

    4. Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

      Note

      Be careful not to damage the retainer.

  9. INSTALL INTAKE VALVE


    1. A01FIPGE38
      Text in Illustration
      *a 40 mm (1.57 in.) or more

      Apply a sufficient coat of engine oil to the tip area of the intake valve shown in the illustration.

    2. Install the intake valve, inner compression spring and valve spring retainer to the cylinder head.

      Note

      Install the same parts in the same combination to their original locations.

    3. A01FERQE01

      Using SST, compress the inner compression spring and install the 2 valve spring retainer locks.

      SST
      09202-70020   ( 09202-00010, 09202-01010, 09202-01020 )

    4. Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

      Note

      Be careful not to damage the retainer.