SFI SYSTEM, Diagnostic DTC:P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135

DESCRIPTION

The throttle position sensor is mounted on the throttle body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The throttle position sensor has 2 sensor circuits, each of which transmits a signal, VTA and VTA2. VTA is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.

P0120, P0122, P0123, P0220, P0222, P0223 and P2135:

• A specific voltage difference is expected between the sensor terminals, VTA and VTA2, for each throttle valve opening angle. If the difference between VTA and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

• VTA and VTA2 each have a specific voltage range. If VTA or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

• VTA and VTA2 should never be close to the same voltage level. If VTA is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor circuit, and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

P0121:

• This sensor transmits two signals: VTA and VTA2. VTA is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA. The ECM performs several checks to confirm the proper operation of the throttle position sensor and VTA.

  For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction in the throttle position sensor. The ECM illuminates the MIL and stores the DTC.

  If the malfunction is not repaired successfully, the DTC is stored 2 seconds after the engine is next started.

MONITOR STRATEGY

CONFIRMATION DRIVING PATTERN

1. Connect the GTS to the DLC3.

2. Turn the engine switch on (IG) and turn the GTS on.

3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) Click here.

4. Turn the engine switch off and wait for at least 30 seconds.

5. Turn the engine switch on (IG) and turn the GTS on [A].

6. Start the engine.

7. With the vehicle stationary, fully depress and release the accelerator pedal [B].

8. Idle the engine for 2 seconds or more [C].

9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10. Read Pending DTCs.

    Tech Tips

    
    

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12. Input the DTC: P0120, P0121, P0122, P0123, P0220, P0222, P0223 or P2135.

13. Check the DTC judgment result.

    Tester Display	Description
    NORMAL	DTC judgment completed System normal
    ABNORMAL	DTC judgment completed System abnormal
    INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions
    N/A	Unable to perform DTC judgment Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    Tech Tips

    
    

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.

FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to electronic throttle control system malfunctions are set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. READ VALUE USING GTS (THROTTLE POSITION SENSOR)

   
   

   1. Connect the GTS to the DLC3.

   2. Start the engine.

   3. Turn the GTS on.

   4. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No.1 and Throttle Position No.2.

   5. Read the values displayed on the GTS.

      Result

      When Accelerator Pedal Fully Released		When Accelerator Pedal Fully Depressed		Trouble Area	Proceed to
      Throttle Position No.1 (VTA)	Throttle Position No.2 (VTA2)	Throttle Position No.1 (VTA)	Throttle Position No.2 (VTA2)
      0 to 0.2 V	0 to 0.2 V	0 to 0.2 V	0 to 0.2 V	VC2 circuit open	A
      4.5 to 4.98 V	4.5 to 4.98 V	4.5 to 4.98 V	4.5 to 4.98 V	E3 circuit open
      0 to 0.2 V, or 4.5 to 4.98 V	2.1 V to 3.1 V (Fail-safe)	0 to 0.2 V, or 4.5 to 4.98 V	2.1 V to 3.1 V (Fail-safe)	VTA circuit open or ground short
      0.6 V to 1.4 V (Fail-safe)	0 to 0.2 V, or 4.5 to 4.98 V	0.6 V to 1.4 V (Fail-safe)	0 to 0.2 V, or 4.5 to 4.98 V	VTA2 circuit open or ground short
      0.5 to 1.1 V	2.1 to 3.1 V	3.2 to 4.8 V (Not fail-safe)	4.6 to 4.98 V (Not fail-safe)	Throttle position sensor circuit normal	B

      Tech Tips

      
      

      • DTC P0121 is stored when the voltages output from VTA and VTA2 are not consistent with the characteristics of the sensors. Therefore, check the Freeze Frame Data when this DTC is output. Use the following formula to confirm relative fluctuations in voltage.

        Characteristics Sensor Output
        VTA2 x 0.8 is approximately equal to VTA + 1.11 V
        VTA: Throttle Position No.1
        VTA2: Throttle position No.2

      • If DTC P0121 is output, proceed to the "CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)".

   
   

   B

   CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) Click here

   A

2. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

   
   

   1. Disconnect the throttle with motor body assembly connector.

   2. Disconnect the ECM connectors.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition F24-5 (VC) - F2-34 (VCTA) Always Below 1 Ω F24-6 (VTA) - F2-26 (VTA) Always Below 1 Ω F24-4 (VTA2) - F2-27 (VTA2) Always Below 1 Ω F24-3 (E2) - F2-35 (ETA) Always Below 1 Ω F24-5 (VC) or F2-34 (VCTA) - Body ground Always 10 kΩ or higher F24-6 (VTA) or F2-26 (VTA) - Body ground Always 10 kΩ or higher F24-4 (VTA2) or F2-27 (VTA2) - Body ground Always 10 kΩ or higher

   4. Reconnect the ECM connectors.

   5. Reconnect the throttle with motor body assembly connector.

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

3. INSPECT ECM (VC VOLTAGE)

   
   
   1. 

      Text in Illustration

      *a	Front view of wire harness connector (to Throttle With Motor Body Assembly)

      Disconnect the throttle with motor body assembly connector.

   2. Turn the engine switch on (IG).

   3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition F24-5 (VC) - F24-3 (E2) Engine switch on (IG) 4.5 to 5.5 V

   4. Reconnect the throttle with motor body assembly connector.

   
   

   NG

   REPLACE ECM Click here

   OK

4. REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

   
   

   1. Replace the throttle with motor body assembly Click here.

   
   

   NEXT

5. CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the engine switch on (IG).

   3. Turn the GTS on.

   4. Clear the DTCs Click here.

   5. Turn the engine switch off and wait for at least 30 seconds.

   6. Turn the engine switch on (IG).

   7. Turn the GTS on.

   8. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

   9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

   10. Read the DTCs.

       Result
       Result Proceed to DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223, and/or P2135 are output A DTC is not output B

   
   

   B

   END

   A

   REPLACE ECM Click here