SFI SYSTEM, Diagnostic DTC:P060E

DTC Code DTC Name
P060E Internal Control Module Throttle Position Performance

MONITOR DESCRIPTION

The ECM monitors the signals of the No. 1 throttle position sensor and stop light switch assembly. When the ECM monitors the input signals of the No. 1 throttle position sensor and the STP signals of the stop light switch assembly, if the input signals and control signals deviate, the DTC is stored.

DTC No. DTC Detection Condition Trouble Area
P060E

Either of the following conditions is met (1 trip detection logic):


  • There is an ECM main CPU error.

  • There is an ECM sub CPU error.

ECM

MONITOR STRATEGY

Required sensors/Components ECM
Frequency of operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

  4. Turn the GTS off.

  5. Turn the engine switch off.

  6. Disconnect the GTS.

  7. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  8. Connect the cable to the negative (-) battery terminal.

  9. Connect the GTS to the DLC3.

  10. Turn the engine switch on (IG) and turn the GTS on.

  11. Wait 16 seconds or more.

  12. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  13. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  15. Input the DTC: P060E.

  16. Check the DTC judgment result.

    GTS Display Description
    NORMAL
    • DTC judgment completed

    • System normal

    ABNORMAL
    • DTC judgment completed

    • System abnormal

    INCOMPLETE
    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions

    N/A
    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

INSPECTION PROCEDURE

Note

After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ OUTPUT DTC (DTC P060E)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs Click here.

    5. Turn the engine switch off.

    6. Turn the GTS off.

    7. Disconnect the GTS.

    8. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

    9. Connect the cable to the negative (-) battery terminal.

    10. Connect the GTS to the DLC3.

    11. Turn the engine switch on (IG).

    12. Turn the GTS on.

    13. Wait 16 seconds or more.

    14. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    15. Read the DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC P060E is output B

    B
    A