SFI SYSTEM, Diagnostic DTC:P0017, P0019

DTC Code DTC Name
P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)
P0019 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)

DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate exhaust valve open and close timing is controlled by the ECM. The ECM performs exhaust valve control by performing the following: 1) controlling the exhaust camshaft and camshaft timing oil control valve assembly (for exhaust camshaft), and operating the camshaft timing exhaust gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. DTC Detection Condition Trouble Area
P0017 Deviations in crankshaft and VVT sensor (for exhaust camshaft) signals (2 trip detection logic)

  • Valve timing

  • Camshaft timing oil control valve assembly for exhaust camshaft (bank 1, 2)

  • Oil control valve filter (bank 1, 2)

  • Camshaft timing exhaust gear assembly

  • ECM
P0019 Deviations in crankshaft and VVT sensor (for exhaust camshaft) signal (2 trip detection logic)

MONITOR DESCRIPTION

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and sets the DTC P0017 (Bank 1) or P0019 (Bank 2).

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing exhaust gear assembly
Required Sensors/Components (Related) VVT sensor, crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Engine speed 500 to 1000 rpm

CONFIRMATION DRIVING PATTERN

A01FEJRE12

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on [A].

  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

  7. Idle the engine for 5 minutes or more [C].

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

  9. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  11. Input the DTC: P0017 or P0019.

  12. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].

  13. Drive the vehicle for 2 to 3 minutes [E].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Idle the engine for 5 minutes or more [F].

  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [G].

  16. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  17. Check the DTC judgment result.

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

Refer to DTC P0013 Click here.

INSPECTION PROCEDURE

Tech Tips


  • The monitor for this DTC detects when the timing chain is shifted by 2 to 3 teeth or more.

  • Bank 1 refers to the bank that includes the No. 1 cylinder*.

    *: The No. 1 cylinder is the cylinder which is farthest from transmission.

  • Bank 2 refers to the bank that does not include the No. 1 cylinder.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0017 OR P0019)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC P0017 or P0019 is output A
      DTC P0017 or P0019 and other DTCs are output B

      Tech Tips

      If any DTCs other than P0017 or P0019 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR (BANK 1 OR 2))


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).

    5. Check the engine speed while operating the camshaft timing oil control valve assembly using the GTS.

      OK
      GTS Operation Engine Condition
      0% Normal engine idle speed
      100% Engine idles roughly or stalls

      Tech Tips

      Refer to "Data List / Active Test" [VVT Ex OCV Duty #1, VVT Ex Chg Angle #1, VVT Ex OCV Duty #2 and VVT Ex Chg Angle #2] Click here.


    NG

    Click here

    OK

  3. CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 OR P0019)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs Click here.

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG) and turn the GTS on.

    7. Start the engine and warm it up.

    8. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    10. Read the pending DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC P0017 or P0019 are output B

      Tech Tips

      DTC P0017 or P0019 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain set even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.


    B

    Click here

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

  4. CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN)


    1. A01FI8DE03
      Text in Illustration
      *1 Timing Mark

      Remove the cylinder head cover sub-assemblies RH and LH.

    2. Turn the crankshaft to align the timing marks of the crankshaft.

    3. Align the notch of the crankshaft pulley to the "0" position.

    4. Check if the timing marks of the camshaft pulley and camshaft bearing cap align.

    5. Turn the crankshaft clockwise 360° if the timing marks do not align. Check if they align once again.

      OK
      The timing marks of the camshaft pulley and the camshaft bearing cap align when the notch of the crankshaft pulley is in the "0" position.

    6. Reinstall the cylinder head cover sub-assemblies RH and LH.


    NG

    ADJUST VALVE TIMING Click here

    OK

  5. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)


    1. Inspect the camshaft timing oil control valve assembly for exhaust camshaft Click here.


    NG

    REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) Click here

    OK

  6. INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE


    1. A01FIA4E05
      Text in Illustration
      *1 Bank 1
      *2 Bank 2

      Remove the No. 1 oil pipe or No. 2 oil pipe.

    2. Remove the oil control valve filter RH or oil control valve filter LH.

    3. Check that the oil control valve filter and oil pipe are not clogged.

      OK
      The oil control valve filter and oil pipe are not clogged.

    4. Reinstall the oil control valve filter RH or oil control valve filter LH.

    5. Reinstall the No. 1 oil pipe or No. 2 oil pipe.


    NG

    REPLACE OIL PIPE OR OIL CONTROL VALVE FILTER Click here

    OK

  7. REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY


    1. Replace the camshaft timing exhaust gear assembly (bank 1 or bank 2) Click here.

      Tech Tips

      Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly Click here.


    NEXT

  8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 OR P0019)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs Click here.

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG) and turn the GTS on.

    7. Start the engine and warm it up.

    8. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

    10. Read the pending DTCs.

      Result
      Result Proceed to
      DTC is not output A
      DTC P0017 or P0019 are output B

    B

    REPLACE ECM Click here

    A

    END