REPAIR INSTRUCTION CUSTOMIZE PARAMETERS


  1. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Tilt & Telescopic / Utility / Customize.

      5. Select the setting by referring to the table below.

        Tilt & Telescopic
        Display Default Content Setting Relevant ECU
        Autoaway/Return function ON Turn the auto away/return function ON or OFF ON/OFF Multiplex tilt and telescopic ECU

  2. CUSTOMIZE LEXUS PARKING ASSIST-SENSOR SYSTEM


    1. Customizing with the GTS

      Note


      • When the customer requests a change in a function, first make sure that the function can be customized.

      • Be sure to make a note of the current settings before customizing.

      • When troubleshooting a function, first make sure that the function is set to the default setting.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the clearance sonar main switch on.

      4. Turn the GTS on.

      5. Enter the following menus: Body Electrical / Utility / Customize.

      6. Select the setting by referring to the table below.

        Warning
        Display Default Content Setting Relevant ECU
        Fr Sensor Onset Range Wide Sets the detection operation range for the front center sensors.

        Narrow or Wide


        • Narrow: 600 mm (23.6 in.)

        • Wide: 1000 mm (39.4 in.)

        		 Clearance warning ECU assembly
        Rr Sensor Onset Range Wide Sets the detection operation range for the rear center sensors.

        Narrow or Wide


        • Narrow: 600 mm (23.6 in.)

        • Wide: 1500 mm (59.1 in.)

        		 Clearance warning ECU assembly
        Keep Sense Buzzer Avail Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.

        Not Avail or Avail


        • Not Avail: Not Available

        • Avail: Available

        		 Clearance warning ECU assembly
        Fr & Rr Buzzer Volume M2 Changes the buzzer volume setting.

        L, M1, M2, M3 or H


        • L: Low volume

        • M1: Medium low volume

        • M2: Medium volume

        • M3: Medium high volume

        • H: High volume

        		 Clearance warning ECU assembly
        Sensor
        Display Default Content Setting Relevant ECU
        Sensor Condition N Avail Makes the front sensors available when the shift lever is in N.

        Not Avail or Avail


        • Not Avail: Not Available

        • Avail: Available

        		 Clearance warning ECU assembly
        Reverse Range Front Sensor Fcrn Changes the operation setting for the front sensors when the shift lever is in R.

        F, Fcrn or F Stop


        • F: All front sensors are available

        • Fcrn: Front corner sensors are available

        • F Stop: All Front sensors are not available

        		 Clearance warning ECU assembly
        Non P/R Range Rear Sensor R Stop Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R.

        R, Rcrn or R Stop


        • R: All rear sensors are available

        • Rcrn: Rear corner sensors are available

        • R Stop: All rear sensors are not available

        		 Clearance warning ECU assembly
        Display
        Display Default Content Setting Relevant ECU
        Display Mode*1 All The display mode setting (when the LEXUS parking assist-sensor system is normal). All or Undisp Clearance warning ECU assembly

        • *1: This item is used to allow or prevent the LEXUS parking assist-sensor system from being displayed on the multi-display assembly. For this model, some vehicles are not equipped with the multi-display assembly. For those vehicles, the Display Mode item is not available.

    2. Customizing with accessory meter assembly*1 or multi-display*2


      • *1: for 12.3 Inch

      • *2: for 8 Inch

      Note


      • When the customer requests a change in a function, first make sure that the function can be customized.

      • Be sure to make a note of the current settings before customizing.

      • When troubleshooting a function, first make sure that the function is set to the default setting.


      1. Turn the engine switch on (IG).

      2. Turn the clearance sonar main switch on.

      3. Enter the following menus: Setup / Vehicle / LEXUS Park Assist.

      4. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Alert volume 3 Sets the buzzer alert volume.

        1, 2, 3, 4 or 5


        • 1: Low volume

        • 2: Medium low volume

        • 3: Medium volume

        • 4: Medium high volume

        • 5: High volume

        		 Clearance warning ECU assembly
        Display On The display mode setting (when the LEXUS parking assist-sensor system is normal). On or Off Clearance warning ECU assembly
        Distance Front Wide Sets the detection operation range for the front center sensors.

        Narrow or Wide


        • Narrow: 600 mm (23.6 in.)

        • Wide: 1000 mm (39.4 in.)

        		 Clearance warning ECU assembly
        Distance Rear Wide Sets the detection operation range for the rear center sensors.

        Narrow or Wide


        • Narrow: 600 mm (23.6 in.)

        • Wide: 1500 mm (59.1 in.)

        		 Clearance warning ECU assembly

  3. CUSTOMIZE POWER DOOR LOCK CONTROL SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS

      Note

      When using the GTS with the engine switch off to troubleshoot:

      Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-seconds intervals until communication between the GTS and vehicle begins.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Door Lock.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Unlock Key Twice

        ON*1

        OFF*2

        		 Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors. ON or OFF Main body ECU (Multiplex network body ECU)
        Auto Lock*3 ON Function that locks all doors when the vehicle speed reaches a certain level. ON or OFF Main body ECU (Multiplex network body ECU)
        Auto Lock/Shift*4 OFF Function that locks all doors when the shift lever is moved out of P, with the engine switch on (IG) and all doors closed. ON or OFF Main body ECU (Multiplex network body ECU)
        Auto Unlock/Shift*5

        ON*6

        OFF*7

        		 Function that unlocks all doors when the shift lever is moved to P from any position other than P with the engine switch on (IG). ON or OFF Main body ECU (Multiplex network body ECU)
        All Unlock/Open-Close

        ON*8

        OFF*9

        		 Function that unlocks the other doors when the driver door is opened within 10 seconds after the engine switch is turned off. ON or OFF Main body ECU (Multiplex network body ECU)

        • *1: for G.C.C. countries, Korea and Australia

        • *2: except G.C.C. countries, Korea and Australia

        • *3: w/ Speed-sensitive Automatic Door Lock Function

        • *4: w/ Shift-linked Automatic Door Lock Function

        • *5: w/ Shift-linked Automatic Door Unlock Function.

        • *6: for Korea

        • *7: except Korea

        • *8: except China, Korea, G.C.C. countries and South Africa

        • *9: for China, Korea, G.C.C. countries and South Africa

    2. Customizing with the Accessory meter*1 or Multi-display*2


      • *1: for 12.3 Inch

      • *2: for 8 Inch


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SET UP/ Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Speed Sensitive Auto Lock*1 On Function that locks all doors when the vehicle speed reaches a certain level. On or Off Main body ECU (Multiplex network body ECU)
        Shift-Linked Auto Lock*4 On Function that locks all doors when the shift lever is moved out of P, with the engine switch on (IG) and all doors closed. On or Off Main body ECU (Multiplex network body ECU)
        Shift-Linked Auto Unlock*5

        On*6

        Off*7

        		 Function that unlocks all doors when the shift lever is moved to P from any position other than P with the engine switch on (IG). On or Off Main body ECU (Multiplex network body ECU)
        Unlock on Second Key turn

        On*2

        Off*3

        		 Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors. On or Off Main body ECU (Multiplex network body ECU)
        Driver Door-Linked Unlock

        On*8

        Off*9

        		 Function that unlocks the other doors when the driver door is opened within 10 seconds after the engine switch is turned off. On or Off Main body ECU (Multiplex network body ECU)

        • *1: w/ Speed-sensitive Automatic Door Lock Function

        • *2: for G.C.C. countries, Korea and Australia

        • *3: except G.C.C. countries, Korea and Australia

        • *4: w/ Shift-linked Automatic Door Lock Function

        • *5: w/ Shift-linked Automatic Door Unlock Function.

        • *6: for Korea

        • *7: except Korea

        • *8: except China, Korea, G.C.C. countries and South Africa

        • *9: for China, Korea, G.C.C. countries and South Africa

  4. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS

      Note

      When using the GTS with the engine switch off to troubleshoot:

      Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-seconds intervals until communication between the GTS and vehicle begins.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Wireless Door Lock.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Wireless Control ON Function that turns wireless door lock OFF or ON Main body ECU (Multiplex network body ECU)
        Hazard Answer Back ON

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 OFF or ON Main body ECU (Multiplex network body ECU)
        Open Door Warning*1 ON The buzzer sounds when lock is pressed when any of the doors are ajar. OFF or ON Main body ECU (Multiplex network body ECU)
        Unlock 2 Operation

        ON*2

        OFF*3

        		 Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. OFF or ON Main body ECU (Multiplex network body ECU)
        Panic Function*2 ON Function to operate theft deterrent system by continuously pressing panic switch on electrical key transmitter sub-assembly for 1.5 seconds OFF or ON Main body ECU (Multiplex network body ECU)
        Trunk Lid Operation Long1

        Function to change the operation method of opening the luggage compartment door by the electrical key transmitter sub-assembly.

        1tim ON: Push the luggage open switch once

        2tim ON: Push the luggage open switch twice

        Long1: Push the luggage open switch for 0.8 seconds

        Long2: Push the luggage open switch for 1.6 seconds

        Prohibit: Wireless luggage compartment door open function is off

        		 1tim ON, 2tim ON, Long1, Long2 or Prohibit Main body ECU (Multiplex network body ECU)
        Auto Lock Time 30 s Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU)
        Wireless Buzzer Resp*2 ON Wireless door lock buzzer response OFF or ON Main body ECU (Multiplex network body ECU)
        P/W Wireless Ope Buzz ON Wireless power window buzzer response OFF or ON Main body ECU (Multiplex network body ECU)
        Wireless Buzzer Vol*2 Level 5 Wireless door lock buzzer volume Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level0 Main body ECU (Multiplex network body ECU)

        • *1: except China

        • *2: except Europe and China

        • *3: for Europe and China

    2. Customizing with the accessory meter asembly*1 or multi-display*2


      • *1: for 12.3 Inch

      • *2: for 8 Inch


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SET UP/ Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Remote 2-Press Unlock On Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is Off, pressing unlock switch once makes all doors unlock. On or Off Main body ECU (Multiplex network body ECU)
        Auto Relock Time Adjust 30 sec. Function that regulates the interval between unlocking and automatic relocking of doors 30 sec., 60 sec. or 120 sec. Main body ECU (Multiplex network body ECU)
        Lock/Unlock Answer Back On

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 On or Off Main body ECU (Multiplex network body ECU)
        Lock Feedback Volume 5 Bars Wireless door lock buzzer volume 0, 1, 2, 3, 4, 5, 6 or 7 Bars Main body ECU (Multiplex network body ECU)

  5. CUSTOMIZE ENTRY AND START SYSTEM (for Entry Function)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Wireless Door Lock, Entry & Start or Warning.

      5. Select the setting by referring to the table below.

        Wireless Door Lock
        Display Default Content Setting Relevant ECU
        Wireless Control ON Function that turns wireless door lock OFF or ON Main body ECU (Multiplex network body ECU)
        Hazard Answer Back ON

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 OFF or ON Main body ECU (Multiplex network body ECU)

        Open Door Warning

        *1

        		 ON The buzzer sounds when lock is pressed when any of the doors are ajar. OFF or ON Main body ECU (Multiplex network body ECU)
        Unlock 2 Operation

        ON*2

        OFF*3

        		 Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock. OFF or ON Main body ECU (Multiplex network body ECU)

        Panic Function

        *2

        		 ON Function to operate theft deterrent system by continuously pressing panic switch on electrical key transmitter sub-assembly for 0.8 seconds OFF or ON Main body ECU (Multiplex network body ECU)
        Trunk Lid Operation Long1

        Function to change the operation method of opening the luggage compartment door by the electrical key transmitter sub-assembly.

        1tim ON: Push the luggage open switch once

        2tim ON: Push the luggage open switch twice

        Long1: Push the luggage open switch for 0.8 seconds

        Long2: Push the luggage open switch for 1.6 seconds

        Prohibit: Wireless luggage compartment door open function is off

        		 1tim ON, 2tim ON, Long1, Long2 or Prohibit Main body ECU (Multiplex network body ECU)
        Auto Lock Time 60 s Function that regulates the interval between unlocking and automatic relocking of doors 30 s, 60 s or 120 s Main body ECU (Multiplex network body ECU)

        Wireless Buzzer Resp

        *2

        		 ON Wireless door lock buzzer response OFF or ON Main body ECU (Multiplex network body ECU)

        Wireless Buzzer Vol

        *2

        		 Level 5 Wireless door lock buzzer volume Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level0 Main body ECU (Multiplex network body ECU)

        • *1: except China

        • *2: except Europe and China

        • *3: for Europe and China

        Entry & Start
        Display Default Content Setting Relevant ECU
        Park Wait Time (Waiting time to permit unlocking door after locking) 2.5s Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed. 0.5s, 1.5s, 2.5s or 5s Certification ECU (smart key ECU assembly)

        Ignition Available Area

        (Entry ignition available area)

        		 All Function that sets the area that the key must be in before the engine switch can be operated. Front or All Certification ECU (smart key ECU assembly)
        Trunk Open Mode ON Function that opens the luggage compartment door when the driver has the electrical key transmitter sub-assembly and presses the luggage door opening switch assembly. OFF or ON Certification ECU (smart key ECU assembly)
        Door Unlock Mode

        Driver*1

        All*2

        		 Function that chooses the doors to be operated by entry unlock operation. All or Driver Certification ECU (smart key ECU assembly)
        Auto Entry Cancel SW OFF Function that enables or disables the entry and start system. OFF or ON Certification ECU (smart key ECU assembly)
        Touch Activation Over Threshold Active The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed. Active or Not Active Certification ECU (smart key ECU assembly)
        Engine Start Indicator ON Function that turns the smart warning light on the combination meter assembly on or off. OFF or ON Certification ECU (smart key ECU assembly)

        • *1: for G.C.C. countries and Australia

        • *2: except G.C.C. countries and Australia

        Warning
        Display Default Content Setting Relevant ECU
        Key Low Battery Warning (Warn when key battery becomes weak) ON Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more. OFF or ON Certification ECU (smart key ECU assembly)

    2. Customizing with the Accessory meter assembly*1 or Multi-display*2


      • *1: for 12.3 Inch

      • *2: 8 Inch


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SET UP/ Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting
        Remote 2-Press Unlock

        On*1

        Off*2

        		 Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is Off, pressing unlock switch once makes all doors unlock. On or Off
        Select Doors to Unlock

        Driver's Door*3

        All Doors*4

        		 Function that sets which doors are unlocked by the entry unlock function. All Doors or Driver's Door
        Auto Relock Time Adjust 60 sec. Function that regulates the interval between unlocking and automatic relocking of doors 30 sec., 60 sec. or 120 sec.

        Lock/Unlock Answer Back

        *1

        		 On

        When the doors are locked by wireless operation, the hazard warning lights flash once.

        When the doors are unlocked by wireless operation, the hazard warning lights flash twice.

        		 On or Off

        Lock Feedback Volume

        *1

        		 5 Bars Wireless door lock buzzer volume 0, 1, 2, 3, 4, 5, 6 or 7 Bars
        Entry and start system On Function that enables or disables the entry and start system. On or Off

        • *1: except Europe and China

        • *2: for Europe and China

        • *3: for G.C.C. countries and Australia

        • *4: except G.C.C. countries and Australia

    3. Entry unlock mode switching function (manual operation)


      1. The following entry unlock modes can be selected when using the entry unlock mode switching function.


        • All door unlock mode: When the sensor of a front door outside handle assembly is touched, an entry unlock operation is performed simultaneously for all doors.

        • Driver door unlock mode: When the sensor of the driver side door outside handle assembly is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.

      2. When customizing through manual operation:


        1. Turn the engine switch off.

        2. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock switches of the electrical key transmitter sub-assembly for 5 seconds or more while the electrical key transmitter sub-assembly is in the actuation area.

        3. Check the current setting.

          Tech Tips


          • The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.

          • The answer-back (wireless buzzer, buzzer in the combination meter assembly) operation for each mode is indicated in the table below.

            Currently Selected Mode Answer-back (Wireless Buzzer) Answer-back (Buzzer in Combination Meter Assembly)
            All door unlock mode Buzzer sounds twice (short beeps) Buzzer sounds once
            Driver door unlock mode Buzzer sounds 3 times (short beeps) Buzzer sounds once

        4. Release the lock and unlock switches of the electrical key transmitter sub-assembly.

        5. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock switches of the electrical key transmitter sub-assembly for 5 seconds or more to change the mode.

          Tech Tips

          Repeat the procedure as necessary to select the desired mode.

        6. Unlock the doors with the wireless operation, and then open any door.

        A01FITJE01

    4. Entry cancel function (manual operation)

      Tech Tips

      While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


      1. The following functions are disabled when the entry and start system is canceled.


        1. Entry unlock/lock functions

        2. Entry luggage compartment door open function

        3. Push start function

        4. Key lock-in prevention function

        5. Entry warning functions

      2. When canceling the system through manual operation:


        1. Make sure the following conditions are met:


          • The engine switch is off.

          • The driver door is closed.

          • The driver door is unlocked.

        2. Press the unlock switch of the electrical key transmitter sub-assembly.

        3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).

        4. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

        5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).

        6. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

        7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).

        8. Close the driver door within 5 seconds of completing the above step.

        9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

        Tech Tips

        Finish the step 5 to 7 within 30 seconds.

      3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.


        1. Perform the procedures to cancel the entry and start system again.

        2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

          Tech Tips


          • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

          • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.

  6. CUSTOMIZE ENTRY AND START SYSTEM (for Start Function)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize / Entry&Start or Warning.

      5. Select the setting by referring to the table below.

        Entry&Start
        Display Default Content Setting Relevant ECU

        Ignition Available Area

        (Entry ignition available area)

        		 All Function that sets the area that the key must be in before the engine switch can be operated. Front or All Certification ECU (smart key ECU assembly)
        Auto Entry Cancel SW OFF Function that enables or disables the entry and start system. OFF or ON
        Engine Start Indicator ON Function that turns the entry warning light on the combination meter assembly on or off. OFF or ON
        Warning
        Display Default Content Setting Relevant ECU
        Key Low Battery Warning (Warn when key battery becomes weak) ON Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more. OFF or ON Certification ECU (smart key ECU assembly)

    2. Customizing with the Accessory meter assembly*1 or Multi-display*2


      • *1: for 12.3 Inch

      • *2: 8 Inch


      1. Turn the engine switch to ON.

      2. Enter the following menus: SETUP / Vehicle / Vehicle Customization / Door Lock Setting.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Entry and start system On Function that enables or disables the entry and start system. On or Off Certification ECU (smart key ECU assembly)

    3. Entry cancel function (manual operation)

      Tech Tips

      While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


      1. The following functions are disabled when the entry and start system is canceled.


        1. Entry unlock/lock functions

        2. Entry luggage compartment door open function

        3. Push-button start function

        4. Key lock-in prevention function

        5. Entry warning functions

      2. When canceling the system through manual operation:


        1. Make sure the following conditions are met:


          • The engine switch is off.

          • The driver door is closed.

          • The driver door is unlocked.

        2. Press the unlock switch of the electrical key transmitter sub-assembly.

        3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).

        4. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

        5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).

        6. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

        7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).

        8. Close the driver door within 5 seconds of completing the above step.

        9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

        Tech Tips

        Finish the step 5 to 7 within 30 seconds.

      3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.


        1. Perform the procedures to cancel the entry and start system again.

        2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

          Tech Tips


          • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

          • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.

  7. CUSTOMIZE PUSH-BUTTON START

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Entry & Start or Warning.

      5. Select the setting by referring to the table below.

        Entry & Start
        Display Default Content Setting Relevant ECU

        Ignition Available Area

        (Entry ignition available area)

        		 All Function that sets the area that the key must be in before the engine switch can be operated. Front or All Certification ECU (smart key ECU assembly)
        Auto Entry Cancel SW OFF Function that enables or disables the push-button start system. OFF or ON Certification ECU (smart key ECU assembly)
        Engine Start Indicator ON Function that turns the smart warning light on the combination meter assembly on or off. OFF or ON Certification ECU (smart key ECU assembly)
        Warning
        Display Default Content Setting Relevant ECU
        Key Low Battery Warning (Warn when key battery becomes weak) ON Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more. OFF or ON Certification ECU (smart key ECU assembly)

    2. Customizing with the Accessory meter assembly*1 or Multi-display*2


      • *1: for 12.3 Inch

      • *2: 8 Inch


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SET UP/ Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting
        Entry and start system On Function that enables or disables the push-button start system. On or Off

    3. Push-button start cancel function (manual operation)

      Tech Tips

      While the push-button start is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter subassembly near the power switch.


      1. The following functions are disabled when the push-button start is canceled.


        1. Push-button start function

        2. Key lock-in prevention function

        3. Entry warning functions

      2. When canceling the push-button start through manual operation:


        1. Make sure the following conditions are met:


          • The power switch is off.

          • The driver door is closed.

          • The driver door is unlocked.

        2. Press the unlock switch of the electrical key transmitter sub-assembly.

        3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).

        4. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

        5. Perform the following procedure within 30 seconds of completing the step above.


          1. Close and open the driver door twice (driver door: open → closed → opened → closed → opened).

          2. With the driver door open, press the unlock switch of the electrical key transmitter subassembly 2 times.

            Note


            • If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

          3. Close and open the driver door (driver door: open → closed → opened).

        6. Close the driver door within 5 seconds (driver door: open → closed).

        7. Check that the wireless buzzer sounds twice (short beeps) to confirm that the push-button start has been canceled.

      3. Perform the following procedure to restore the push-button start to the active state from the canceled state.


        1. Perform the procedures to cancel the push-button start again.

        2. Check that the wireless buzzer sounds once (short beep) to confirm that the push-button start has been restored to the active state.

          Tech Tips


          • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

          • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.

  8. CUSTOMIZE THEFT DETERRENT SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Security or Wireless Door Lock.

      5. Select the setting by referring to the table below.

        Security
        Display Default Content Setting Relevant ECU
        Window Open Warning ON This function is used to enable or disable the Window open warning. OFF/ON Main Body ECU (Multiplex Network Body ECU)
        Slide Roof Open Warning ON This function is used to enable or disable the sliding roof open warning. OFF/ON
        Intrusion Win Opened*1 OFF Sets the sensitivity of the intrusion sensor when the windows are opened. OFF/ON
        Security control with mechanism key*2 OFF This function makes it possible to cancel the security alarm with the mechanical key. OFF/ON
        Intrusion Sensor Sensitivity Level*3 N+Sound

        Sets the sensor sensitivity for operating the alarm when an intrusion is detected.


        • Normal: Use this setting when the customer wants to detect moving objects regardless of whether glass is broken or not.

        • Low: Use this setting when the customer wants the sensitivity to be low. This setting is effective for normal use, but the alarm still operates when a person, pet, etc. is inside of the vehicle when the alarm is set.

        Note

        Using any settings other than N+Sound, Normal and Low is prohibited.

        		 Highest / High / Normal / N+Sound / Low / Lowest

        • *1: w/ Intrusion Sensor Cancel Switch

        • *2: Vehicles displaying the Item "Security control with mechanism key" on the GTS

        • *3: w/o Door Ajar Warning Buzzer Function

        Wireless Door Lock
        Display Default Content Setting Relevant ECU
        Panic Function* ON This function operates the theft deterrent system when the panic switch is pressed and held for 1.5 seconds. OFF/ON Main Body ECU (Multiplex Network Body ECU)

        • *: w/ Panic Switch

  9. CUSTOMIZE LIGHTING SYSTEM (INT)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Utility / Customize / (desired system).

      5. Select the setting by referring to the table below.

        Illuminated Entry
        Display Default Content Setting Relevant ECU
        Lighting Time 15 s Changes the lighting time after closing all of the doors [It will fade out immediately when turning the engine switch from off to on (ACC) or on (IG)]. 7.5 s, 15 s or 30 s Main body ECU (Multiplex network body ECU)
        I/L when ACC OFF ON A function that turns on the interior lights when the engine switch is turned from on (IG) or on (ACC) to off (the interior lights turn on when the map light switch is set to DOOR). ON or OFF
        I/L ON W/Door Key Unlock ON A function that turns on the interior lights when the door is unlocked (the interior lights turn on when the map light switch is set to DOOR). ON or OFF
        Room Light when Aprchd ON A function that turns on the room lights when the key is brought within the vehicle exterior detection area (the room lights turns on when the map light switch is set to DOOR). ON or OFF
        Inside Foot Light ON Changes the interior foot lights control. ON or OFF
        Mirr-Foot-Lgt Approached ON Lights up the door mirror foot lights when the key is brought within the vehicle exterior detection area. ON or OFF
        Mirr-Foot-Lgt Unlocked ON Lights up the door mirror foot lights when the doors are unlocked using a mechanical key or door control transmitter. ON or OFF
        Mirror Foot Light Time 15 s Changes the lighting time of the door mirror foot lights. 7.5 s, 15 s or 30 s
        Light Control ON This function controls the interior foot lights, inside handle illumination and door ambient light. ON or OFF
        Interior Light Control ON This function controls the interior lights. ON or OFF
        Exterior Light Control ON This function controls the door mirror foot lights. ON or OFF
        Light Control
        Display Default Content Setting Relevant ECU
        Light up Clearance Lights at Door Unlock Function ON A function that turns on the clearance lights, taillights and license plate lights for 15 seconds when the doors are unlocked by an entry unlock operation or wireless unlock operation. ON or OFF Main body ECU (Multiplex network body ECU)

    2. Customizing with Multi-display.


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle / Vehicle Settings / Vehicle Customization / Light Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Interior Lights Off Time 15 s This function controls the interior lights. OFF, 7.5 s, 15 s or 30 s Main body ECU (Multiplex network body ECU)
        Exterior Lights Off Time 15 s This function controls the door mirror foot lights. OFF, 7.5 s, 15 s or 30 s

  10. CUSTOMIZE METER / GAUGE SYSTEM


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Combination Meter / Warning or Display.

      5. Select the setting by referring to the table below.

        Warning
        Display Default Content Setting Relevant ECU
        Driver Side Seatbelt Warning Buzzer* ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly
        Front Passenger Side Seatbelt Warning Buzzer* ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly
        Flasher Sound Volume Adjustment Large Function to change the flasher sound volume Large, Medium or Small Combination meter assembly

        • *: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more

        Display
        Display Default Content Setting Relevant ECU
        ECO Drive Indicator Zone ON Function to enable or disable eco driving indicator zone display in the multi-information display ON or OFF Combination meter assembly
        ODO Display Time After IG OFF Setting 30 s Function to change the odometer display time 30 s, 60 s, 600 s or OFF Combination meter assembly

    2. Customizing with the combination meter assembly


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Settings.

      3. Select the setting by referring to the table below.

        Meter Setting
        Display Default Content Setting Relevant ECU
        Language American English Function to change the multi-information display language American English, Francais, Deutsch, Espanol, Italiano or pyccknn Combination meter assembly
        Units km (L/100km) Function to change the multi-information display unit km (km/L) or km (L/100km) Combination meter assembly
        ECO Indicator ON (Automatic) Function to turn on/off the eco light ON (Automatic), OFF or ON (Always) Combination meter assembly
        Drive monitor Outside Function to change the drive monitor setting Gas mileage, Cruising range or Outside Combination meter assembly
        Lamp brightness Standard Function to change the meter illumination setting Bright or Standard Combination meter assembly
        SPORT lamp ON Function to turn on/off the SPORT light setting ON or OFF Combination meter assembly
        Default Setting OFF Function to turn on/off the default setting ON or OFF Combination meter assembly

  11. CUSTOMIZE FRONT POWER SEAT CONTROL SYSTEM (for LHD)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Seat.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Seat Move Distance Standard Allows customizing of the seat movement distance for the power easy access system. ON or OFF Main body ECU (multiplex network body ECU)
        R&A Side Support Oper ON When the "Return & Away" operates, the function that D-seat "Side Support" operates is stopped when it is "OFF". ON or OFF Position control ECU assembly*1, *2, *3
        R&A Lumbar Support Oper ON When the "Return & Away" operates, the function that D-seat "Lumbar Support" operates is stopped when it is "OFF". ON or OFF Position control ECU assembly*1, *2, *3
        R&A Pelvis Support Oper ON When the "Return & Away" operates, the function that D-seat "Pelvis" operates is stopped when it is "OFF". ON or OFF Position control ECU assembly*1, *2, *3
        R&A Ottoman Operation ON When the "Return & Away" operates, the function that "Ottoman Operation" operates is stopped when it is "OFF". ON or OFF Position control ECU assembly*4

        • *1: for Driver Side, Sports Seat Type

        • *2: for Driver Side, Luxury Seat Type

        • *3: for Front Passenger Side, Luxury Seat Type

        • *4: for Ottoman

      6. Enter the following menus: Customize Setting / Smart Key / Access.

      7. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Seat position/Tilt & Telesco memory recall setting D Door This customize function switches the condition of the seat position and Tilt & Telesco memory recall. Possible recall activation parameter "D-door unlock and open by smart system" or "Any door unlock and open with smart system" D-Door / ANY Door Certification ECU (smart key ECU assembly)

    2. Customizing with the Multi-display


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SET UP / Vehicle / Vehicle Customization / Other vehicle settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Driver's seat easy exit Full Allows customization of the seat movement distance for the power easy access system. Full / Partial / Off Main body ECU (multiplex network body ECU)

  12. CUSTOMIZE FRONT POWER SEAT CONTROL SYSTEM (for RHD)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Seat.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Seat Move Distance Standard Allows customizing of the seat movement distance for the power easy access system. ON or OFF Main body ECU (multiplex network body ECU)
        R&A Side Support Oper ON When the "Return & Away" operates, the function that "Side Support" operates is stopped when it is "OFF". ON or OFF Position control ECU assembly*1, *2, *3
        R&A Lumbar Support Oper ON When the "Return & Away" operates, the function that "Lumbar Support" operates is stopped when it is "OFF". ON or OFF Position control ECU assembly*1, *2, *3
        R&A Pelvis Support Oper ON When the "Return & Away" operates, the function that "Pelvis" operates is stopped when it is "OFF". ON or OFF Position control ECU assembly*1, *2, *3
        R&A Ottoman Operation ON When the "Return & Away" operates, the function that "Ottoman Operation" operates is stopped when it is "OFF". ON or OFF Position control ECU assembly*4

        • *1: for Driver Side, Sports Seat Type

        • *2: for Driver Side, Luxury Seat Type

        • *3: for Front Passenger Side, Luxury Seat Type

        • *4: for Ottoman

      6. Enter the following menus: Customize Setting / Smart Key / Access.

      7. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Seat position/Tilt & Telesco memory recall setting D Door This customize function switches the condition of the seat position and Tilt & Telesco memory recall. Possible recall activation parameter "D-door unlock and open by entry and start system" or "Any door unlock and open with smart system" D-Door / ANY Door Certification ECU (smart key ECU assembly)

    2. Customizing with the Multi-display


      1. Turn the engine switch on (IG).

      2. Enter the following menus: SET UP / Vehicle / Vehicle Customization / Other vehicle settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Driver's seat easy exit Full Allows customization of the seat movement distance for the power easy access system. Full / Partial / Off Main body ECU (multiplex network body ECU)

  13. CUSTOMIZE SEAT HEATER SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Air Conditioner.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Seat Heater Auto Operation ON Function that links the seat heater to ECO mode and the seat heater timer ON/OFF operation ON or OFF Air conditioning amplifier assembly

    2. Customizing using the accessory meter assembly*1 or multi-display*2


      • *1: for 12.3 Inch

      • *2: for 8 Inch


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Climate Settings /.

      3. Select the setting by referring to the table below:

        Climate Settings
        Display Default Contents Setting Relevant
        Auto Seat A/C HTR Temp. FR L 0 When in AUTO, this function automatically adjusts the temperature of the seat heater -2/-1/0/+1/+2 Climate control ECU
        Auto Seat A/C HTR Temp. FR R 0 When in AUTO, this function automatically adjusts the temperature of the seat heater -2/-1/0/+1/+2 Climate control ECU
        Auto Seat HTR Temp. RR L* 0 When in AUTO, this function automatically adjusts the temperature of the seat heater -2/-1/0/+1/+2 Climate control ECU
        Auto Seat HTR Temp. RR R* 0 When in AUTO, this function automatically adjusts the temperature of the seat heater -2/-1/0/+1/+2 Climate control ECU
        Auto Seat HTR RR L Default* On This function allows the rear seat heater setting to be selected when the engine switch is on (IG) On/Off Climate control ECU
        Auto Seat HTR RR R Default* On This function allows the rear seat heater setting to be selected when the engine switch is on (IG) On/Off Climate control ECU

        • *: w/ Rear Seat Heater

  14. CUSTOMIZE SEAT BELT WARNING SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.

    • These buzzers should be ON for safe driving. Perform this procedure only if it is necessary to set the buzzer to OFF (disabled).


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body / Combination Meter / Utility / Customize / Warning.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Driver Side Seatbelt Warning Buzzer ON Function to sound the driver seat belt warning buzzer ON/OFF Combination meter assembly
        Front passenger Side Seatbelt Warning Buzzer ON Function to sound the front passenger seat belt warning buzzer ON/OFF

        Tech Tips

        This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.

  15. CUSTOMIZE AIR CONDITIONING SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS.


      1. Connect the GTS.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / .

      5. Select the setting by referring to the table below.

        Air Conditioner
        Tester Display Default Content Setting Relevant ECU
        Set Temperature Shift Normal Function to perform control with the shifted temperature versus the displayed temperature -2C, -1C, Normal, +1C, +2C Air Conditioning Amplifier Assembly
        Evaporator Control Automatic Function to set the evaporator control to the AUTOMATIC position (AUTO) to save power or to the coldest position (MANUAL) to dehumidify the air and to prevent the windows from fogging up Automatic or Manual Air Conditioning Amplifier Assembly
        Compressor Mode Automatic Enables or disables the function which automatically turns the air conditioning on according to the state of the AUTO switch. Automatic or Manual Air Conditioning Amplifier Assembly
        Air Inlet Mode Automatic Enables or disables the function which automatically switches between recirculation and fresh air modes when the AUTO switch is on. Automatic or Manual Air Conditioning Amplifier Assembly
        Foot/DEF Auto Mode ON Function to turn the airflow from Foot/DEF ON automatically when the AUTO switch is on ON or OFF Air Conditioning Amplifier Assembly
        Foot/DEF Automatic Blow Up Function ON Function to increase the blower level automatically when the defroster is ON ON or OFF Air Conditioning Amplifier Assembly
        Ambient Temperature Shift Normal Function to display shifted ambient temperature versus actual ambient temperature -3C, -2C, -1C, Normal, +1C, +2C, +3C Air Conditioning Amplifier Assembly
        Emission Gas Sensor Shift* Normal Function to change the sensitivity of the smog ventilation sensor. Much Less, Less, Little Less, Normal, Little More, More, Much More Air Conditioning Amplifier Assembly
        Add Foot Air in FACE Mode ON When the FACE mode is selected, an additional amount of air blown to the foot area. Selecting OFF will cancel this additional air flow. ON or OFF Air Conditioning Amplifier Assembly
        ECO MODE Cancel OFF Function to cancel the ECO drive mode when item is ON. ON or OFF Air Conditioning Amplifier Assembly
        Refrigerant Shortage Check ON Function to cancel the refrigerant shortage check (check performed during normal operation) when item is OFF ON or OFF Air Conditioning Amplifier Assembly
        Fan speed increment control Normal Function to define how fast the blower goes to target speed when first activating the air conditioning system Slow, Normal, Fast Air Conditioning Amplifier Assembly

        • *: w/ Smog Ventilation Sensor

    2. Customizing using the multi-display (for 8 Inch) or accessory meter assembly (for 12.3 Inch)


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Climate Settings /.

      3. Select the setting by referring to the table below:

        Climate Settings
        Display Default Content Setting Relevant ECU
        Smog Sensor Sensitivity* 0 Changes the sensitivity of the exhaust gas sensor. -2, -1, 0, +1, +2 Air conditioning amplifier assembly
        Auto A/C Mode On Enables or disables the function which automatically turns the air conditioning on according to the state of the AUTO switch. On or Off Air conditioning amplifier assembly
        Efficient Ventilation Mode On Enables or disables the function which automatically switches between recirculation and fresh air modes when the AUTO switch is on. On or Off Air conditioning amplifier assembly

        • *: w/ Smog Ventilation Sensor

  16. CUSTOMIZE REAR SUNSHADE SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting.

      5. Select the setting by referring to the table below.

        Others
        System Default Contents Setting Relevant ECU
        Rear Shade Delay Time 0.7 s The function to adjust the reverse-linked sunshade lowering function's response time. 0.7 s, 1.2 s, 0.9 s or 0.0 s Main body ECU (multiplex network body ECU)
        R-pos to Rear Sun Shade COM ON The reverse-linked function. ON or OFF Main body ECU (multiplex network body ECU)

  17. CUSTOMIZE POWER WINDOW CONTROL SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Utility / Customize / Power Window.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Door Key P/W Up OFF This function is used to close the windows by operating the mechanical key. ON or OFF Main body ECU (Multiplex network body ECU)
        Door Key P/W Down OFF This function is used to open the windows by operating the mechanical key. ON or OFF Main body ECU (Multiplex network body ECU)
        P/W Up w/ Transmitter* OFF This function is used to close the windows using the wireless key transmitter. ON or OFF Main body ECU (Multiplex network body ECU)
        P/W Down w/ Transmitter* OFF This function is used to open the windows using the wireless key transmitter. ON or OFF Main body ECU (Multiplex network body ECU)
        P Window Auto Up Avail This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger side). Avail or Not Avl Power window ECU (Power window regulator motor assembly)
        P Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly. Avail or Not Avl Power window ECU (Power window regulator motor assembly)
        RR Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH side). Avail or Not Avl Power window ECU (Power window regulator motor assembly)
        RR Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly. Avail or Not Avl Power window ECU (Power window regulator motor assembly)
        RL Window Auto Up Avail This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH side). Avail or Not Avl Power window ECU (Power window regulator motor assembly)
        RL Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly. Avail or Not Avl Power window ECU (Power window regulator motor assembly)

        • *: w/ Wireless Transmitter-Linked Function

      6. Enter the following menus: Utility / Customize / Main Body.

      7. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Window Open Warning ON This function is used to enable or disable the power window open warning. ON or OFF Main body ECU (Multiplex network body ECU)

  18. CUSTOMIZE SLIDING ROOF SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Power Window.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Door Key P/W Up OFF This function is used to close the driver door window and sliding roof by operating the mechanical key. OFF/ON Main body ECU (Multiplex network body ECU)
        Door Key P/W Down OFF This function is used to open the driver door window and sliding roof by operating the mechanical key. OFF/ON Main body ECU (Multiplex network body ECU)
        P/W Down W/ Transmit OFF This function is used to open the driver door window and sliding roof using the wireless key transmitter. OFF/ON Main body ECU (Multiplex network body ECU)

      6. Enter the following menus: Customize Setting / Slide Roof.

      7. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Door Key Related Operation*1 Slide Function to select tilt up or slide open of sliding roof key-linked function. Slide/Tilt Sliding roof drive gear sub-assembly (Sliding roof ECU)
        Wireless Key Related Operation*2 Slide Function to select tilt up or slide open of sliding roof wireless transmitter-linked function. Slide/Tilt Sliding roof drive gear sub-assembly (Sliding roof ECU)
        Front SW Auto Operation ON This function is used to enable or disable the auto operation. OFF/ON Sliding roof drive gear sub-assembly (Sliding roof ECU)

        • *1: This function is linked with the power window key-linked function. If the power window key-linked function is set to OFF, the sliding roof key-linked function will not operate even when it is set to ON.

        • *2: This function is linked with the power window wireless transmitter-linked function. If the power window wireless transmitter-linked function is set to OFF, the sliding roof wireless transmitter-linked function will not operate even when it is set to ON.

      8. Enter the following menus: Customize Setting / Security.

      9. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Slide Roof Open Warning ON This function is used to enable or disable the sliding roof open warning. OFF/ON Main body ECU (Multiplex network body ECU)

  19. CUSTOMIZE LUGGAGE COMPARTMENT DOOR OPENER SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS.

      Note

      When using the GTS with the engine switch off to troubleshoot:

      Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-seconds intervals until communication between the GTS and vehicle begins.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Door Lock.

      5. Select the setting by referring to the table below:

        Door Lock
        Display Default Content Setting Relevant ECU
        Trunk Link with Door Lock ON Function that opens the luggage compartment door when the luggage electrical key switch is pressed and all doors are unlocked. ON or OFF Main body ECU (multiplex network body ECU)

  20. CUSTOMIZE POWER TRUNK LID SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS.

      Note

      When using the GTS with the engine switch off to troubleshoot:

      Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-seconds intervals until communication between the GTS and vehicle begins.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Back Door or Door Lock.

      5. Select the setting by referring to the table below:

        Back Door
        Display Default Content Setting Relevant ECU
        PBD Power Operation ON Turns power trunk opener and closer function ON or OFF. ON or OFF Luggage closer motor assembly
        Door Lock
        Display Default Content Setting Relevant ECU
        Trunk Link with Door Lock ON Function that opens the luggage compartment door when the luggage electrical key switch is pressed and all doors are unlocked. ON or OFF Main body ECU (multiplex network body ECU)

  21. CUSTOMIZE POWER MIRROR CONTROL SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Utility / Customize / Others.

      5. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Auto Fold Mirror* Door Lock Function that changes the condition under which the door mirrors automatically retract. ACC, Door Lock or OFF Main body ECU (Multiplex network body ECU)
        Reverse Coupled Actuation Mirror Angle ON Function that turns the door mirror reverse shift-linked function on or off ON or OFF Main body ECU (Multiplex network body ECU)

        • *: w/ Retract Mirror

  22. CUSTOMIZE LIGHTING SYSTEM (EXT)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Utility / Customize / (desired system).

      5. Select the setting by referring to the table below.

        Warning
        Display Default Content Setting Relevant ECU
        Flasher Sound Volume Adjustment Large Function to change the flasher sound volume adjustment. Large, Medium or Small Combination meter assembly
        Light Control
        Display Default Content Setting Relevant ECU
        Disp Ex ON Sen Normal Changes the level of ambient light at which the system dims lights such as the indicator lights of the combination meter, the A/ C indicator light and the clock.*3 LIGHT2, LIGHT1, NORMAL, DARK1 or DARK2 Main body ECU (Multiplex network body ECU)
        Disp Ex OFF Sen Normal Changes the level of ambient light at which the system cancels the dimming of lights such as the indicator lights of the combination meter, the A/C indicator light and the clock.*4 LIGHT2, LIGHT1, NORMAL, DARK1 or DARK2 Main body ECU (Multiplex network body ECU)
        Light Auto OFF Delay*1 30 s Function to continue illuminating the headlights and taillights for a certain period of time after closing the driver door after the engine switch is turned from on (IG) to off with the headlight dimmer switch in the AUTO position and the headlights and taillights on. OFF, 30 s, 60 s or 90 s Main body ECU (Multiplex network body ECU)
        Sensitivity Normal Adjusts the ambient light sensitivity of the automatic light control system.*5 Light2, Light1, Normal, Dark1 or Dark2 Main body ECU (Multiplex network body ECU)
        DRL Function*6 ON A function that enables or disables the DRL. ON or OFF Main body ECU (Multiplex network body ECU)
        Follow Me Home Lighting Time*2 30 s Changes the low beam headlight lighting time when engine switch is off and headlight dimmer switch is pulled to flash headlights once. 30 s, 60 s, 90 s, or 120 s Main body ECU (Multiplex network body ECU)

        • *1: w/ Light Auto Turn-off Delay Function

        • *2: w/ Follow Me Home System

        • *6: w/o Automatic Recirculation Control

        Tech Tips

        The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

        *3
        System Setting A01FHQ4
        Setting DARK2 DARK1 NORMAL LIGHT1 LIGHT2

        Tech Tips

        When the setting is closer to the "Light" side, the system dims the indicator lights even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before dimming the indicator lights.

        *4
        System Setting A01FHQ4
        Setting DARK2 DARK1 NORMAL LIGHT1 LIGHT2

        Tech Tips

        When the setting is closer to the "Dark" side, the system cancels the dimming of the indicator lights even when the surrounding area is relatively dark. When the setting is closer to the "Light" side, the system waits until the surrounding area is brighter before canceling the dimming of the indicator lights.

        *5
        System Setting A01FHQ4
        Setting Dark2 Dark1 Normal Light1 Light2

        Tech Tips

        When the setting is closer to the "Light" side, the system turns the lights on even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before turning on the lights.

    2. Customizing with Multi-display.


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle / Vehicle Settings / Vehicle Customization / Light Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Light Sensor Sensitivity

        0

        (middle bar)

        		 Adjusts the ambient light sensitivity of the automatic light control system.*2 -2, -1, 0, +1 or +2 Main body ECU (Multiplex network body ECU)
        Headlights Off Time*1 30 s Function to continue illuminating headlights and taillights for a certain period of time after closing driver door with the engine switch turned from on (IG) to off under the condition that the headlight dimmer switch is in the AUTO position with the headlights and taillights on. Off, 30 s, 60 s or 90 s
        Daytime Running Lights On A function that enables or disables the DRL. On or Off

        • *1: w/ Light Auto Turn-off Delay Function

        Tech Tips

        The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

        *2
        System Setting A01FHQ4
        Setting -2 -1 0 +1 +2

        Tech Tips

        When the setting is closer to the "Light" side, the system turns the lights on even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before turning on the lights.

    3. Customization of lane change flasher and turn cancel functions


      1. Customize the lane change flasher and turn cancel functions by following the procedures shown below.

        Step Operation Remark
        1

        1. Turn the engine switch off.

        2. Move the windshield wiper switch assembly and headlight dimmer switch assembly to the NEUTRAL position.

        		 -
        2

          When setting the lane change flasher control to on:

        1. Set the number of blinks for the lane change flasher control.


          1. Refer to the following items and select wiper speed switch position P1, P2 or P3.


            1. Blinks 3 times: P1

            2. Blinks 5 times: P2

            3. Blinks 7 times: P3

          When setting the lane change flasher control to off:

        1. Select wiper speed switch position P4.

        		 Do not operate the wiper speed switch after step 3.
        3

        1. Move the windshield wiper switch assembly from the NEUTRAL position to the OFF position and hold it there.

        • Steps 3, 4 and 5 are operations for changing to lane change flasher setting mode.

        • If operations other than those described in steps 3, 4 or 5 are performed, the control will change to normal mode. Start from step 1 again.
        4

        1. Turn the engine switch on (IG).
        5

          Perform the following operations:

        1. Keep the windshield wiper switch assembly in the OFF position for 5 seconds or more.

        2. Move the windshield wiper switch assembly from the OFF position to the WPDN position.

        3. Keep the windshield wiper switch assembly in the WPDN position for 5 seconds or more.

        4. Move the windshield wiper switch assembly from the WPDN position to the OFF position.

        5. Perform operations 1 to 3 again.

        6. Move the windshield wiper switch assembly from the WPDN position to the NEUTRAL position.
        6

        1. Check that the mode has changed to lane change flasher control setting mode.

          OK
          The right turn signal lights blink once.
        		While changing to lane change flasher control setting mode, wiper control and turn signal light control cannot be performed.
        7

        1. Confirm the selected setting (number of blinks) by performing the following operations:


          1. Move the headlight dimmer switch assembly from the NEUTRAL position to the left lane change position.

          2. Move the headlight dimmer switch assembly to the NEUTRAL position.

        1. Set and confirm the canceling method by performing the following operations:


          • Canceling by operating the lever in the opposite direction


            1. Move the headlight dimmer switch assembly from the NEUTRAL position to the left lane change position.

            2. Move the headlight dimmer switch assembly to the NEUTRAL position.

          • Canceling by operating the lever in the same direction


            1. Move the headlight dimmer switch assembly from the NEUTRAL position to the right lane change position.

            2. Move the headlight dimmer switch assembly to the NEUTRAL position.

        • If operations other than those described in step 7 are performed, the control will change to normal mode. Start from step 1 again.

        • Make sure to finish step 7 within approximately 20 seconds.
        8

        1. Check the answer back for completion of setting the number of blinks of the lane change flasher control.


          • Blinks 3 times

            OK
            The left turn signal lights blink once.

          • Blinks 5 times

            OK
            The left turn signal lights blink twice.

          • Blinks 7 times

            OK
            The left turn signal lights blink 3 times.

        1. Check the answer back for completion of changing the turn cancel function.


          • Canceling by operating the lever in the opposite direction

            OK
            Canceling by operating the lever in the opposite direction

          • Canceling by operating the lever in the same direction

            OK
            The left turn signal lights blink 5 times.

          If the answer back cannot be confirmed:

        • If 20 seconds or more had elapsed while performing step 7, the control will have changed to normal mode. Start from step 1 again.
        9 Setting is complete. Lane change flasher control setting mode changes to normal mode.

      2. for LHD

        A01FGF3E01
        Text in Illustration
        *1 Right Turn *2 Right Lane Change
        *3 NEUTRAL *4 Left Lane Change
        *5 Left Turn *6 Wiper Speed Setting P4
        *7 Wiper Speed Setting P3 *8 Wiper Speed Setting P2
        *9 Wiper Speed Setting P1 *10 Off
        *11 WPDN *12 NEUTRAL
        *13 WPUP *14 HI
        *15 Headlight Dimmer Switch Assembly *16 Windshield Wiper Switch Assembly

      3. for RHD (Dimmer Switch RH Side)

        A01FGILE01
        Text in Illustration
        *1 Wiper Speed Setting P4 *2 Wiper Speed Setting P3
        *3 Wiper Speed Setting P2 *4 Wiper Speed Setting P1
        *5 Off *6 WPDN
        *7 NEUTRAL *8 WPUP
        *9 HI *10 Left Turn
        *11 Left Lane Change *12 NEUTRAL
        *13 Right Lane Change *14 Right Turn
        *15 Windshield Wiper Switch Assembly (for LH Side) *16 Headlight Dimmer Switch Assembly (for RH Side)

      4. for RHD (Dimmer Switch LH Side)

        A01FGF3E01
        Text in Illustration
        *1 Right Turn *2 Right Lane Change
        *3 NEUTRAL *4 Left Lane Change
        *5 Left Turn *6 Wiper Speed Setting P4
        *7 Wiper Speed Setting P3 *8 Wiper Speed Setting P2
        *9 Wiper Speed Setting P1 *10 Off
        *11 WPDN *12 NEUTRAL
        *13 WPUP *14 HI
        *15 Headlight Dimmer Switch Assembly (for LH Side) *16 Windshield Wiper Switch Assembly (for RH Side)