REAR DIFFERENTIAL CARRIER OIL SEAL (for 4GR-FSE) REPLACEMENT


  1. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY

    Click here

  2. REMOVE REAR DIFFERENTIAL CARRIER COVER


    1. A01FGSA

      Remove the 8 bolts.

    2. A01FDHJ

      Using a brass bar and hammer, remove the rear differential carrier cover from the rear differential carrier.

      Note


      • Place the brass bar onto the corners of the rear differential carrier cover.

      • Do not damage the sealing surface of the rear differential carrier.

  3. SECURE REAR DIFFERENTIAL CARRIER


    1. A01FEM6

      Install the rear differential carrier to the overhaul stand as shown in the illustration.

  4. REMOVE REAR DRIVE PINION NUT


    1. A01FHSBE01

      Using SST and a hammer, unstake the staked part of the rear drive pinion nut.

      SST
      09930-00010

      Note


      • Be sure to use SST with the tapered surface facing the differential drive pinion.

      • Do not grind the tip of SST with a grinder, etc.

      • Completely loosen the staked part of the rear drive pinion nut when removing it.

      • Do not damage the threads of the differential drive pinion.

    2. A01FGZOE03
      Text in Illustration
      *a Turn
      *b Hold

      Using SST to hold the rear drive pinion companion flange, remove the rear drive pinion nut.

      SST
      09330-00021

  5. REMOVE REAR DRIVE PINION COMPANION FLANGE


    1. A01FFHCE03
      Text in Illustration
      *a Turn
      *b Hold

      Using SST, remove the rear drive pinion companion flange.

      SST
      09950-30012   ( 09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030 )

      Note

      Apply grease to the threads of SST center bolt before use.

  6. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


    1. A01FFXJE03
      Text in Illustration
      *1 Rear Differential Carrier Oil Seal

      Using SST, remove the rear differential carrier oil seal from the rear differential carrier.

      SST
      09308-00010

  7. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


    1. A01FGFW

      Remove the rear differential drive pinion oil slinger.

  8. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    1. A01FG2YE03
      Text in Illustration
      *a Turn
      *b Hold

      Using SST, remove the rear drive pinion front tapered roller bearing inner race from the differential drive pinion.

      SST
      09556-22010

      Note

      Apply grease to the threads and tip of SST center bolt before use.

  9. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


    1. A01FIXA

      Remove the rear differential drive pinion bearing spacer.

  10. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


    1. A01FIXA

      Install a new rear differential drive pinion bearing spacer to the differential drive pinion.

      Note

      Be sure to install the spacer so that the side with the larger inner diameter faces the rear differential carrier as shown in the illustration.

  11. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    1. A01FGLR

      Install the rear drive pinion front tapered roller bearing to the differential drive pinion.

  12. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


    1. A01FGFW

      Install the rear differential drive pinion oil slinger to the differential drive pinion.

  13. INSTALL REAR DRIVE PINION COMPANION FLANGE


    1. A01FF29E03
      Text in Illustration
      *a Turn
      *b Hold

      Using SST and a rear drive pinion companion flange, install the rear drive pinion companion flange and rear drive pinion front tapered roller bearing.

      SST
      09950-30012   ( 09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030 )

      Note

      Apply grease to the threads of SST center bolt before use.

  14. REMOVE REAR DRIVE PINION COMPANION FLANGE


    1. A01FFHCE03
      Text in Illustration
      *a Turn
      *b Hold

      Using SST, remove the rear drive pinion companion flange.

      SST
      09950-30012   ( 09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030 )

      Note

      Apply grease to the threads of SST center bolt before use.

  15. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


    1. A01FDMAE05
      Text in Illustration
      *1 Rear Differential Carrier Oil Seal

      Using SST and a hammer, install a new rear differential carrier oil seal.

      SST
      09554-22010
      Standard depth
      1.55 to 2.45 mm (0.0610 to 0.0964 in.)

      Note


      • Tap the oil seal uniformly so that the oil seal is straight.

      • Do not excessively tap the oil seal.

  16. INSTALL REAR DRIVE PINION COMPANION FLANGE


    1. A01FF29E03
      Text in Illustration
      *a Turn
      *b Hold

      Using SST, install the rear drive pinion companion flange.

      SST
      09950-30012   ( 09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030 )

      Note

      Apply grease to the threads of SST center bolt before use.

    2. Coat the threads of the rear drive pinion nut with hypoid gear oil LSD.

    3. A01FEWXE03
      Text in Illustration
      *a Turn
      *b Hold

      Using SST and a torque wrench, hold the rear drive pinion companion flange and tighten the rear drive pinion nut.

      SST
      09330-00021
      Torque:
      337 N*m  { 3444 kgf*cm, 249 ft.*lbf, or less }

      Note


      • Tighten the rear drive pinion nut to approximately 100 N*m (1020 kgf*cm, 74 ft.*lbf), and then tighten it further while checking the differential drive pinion preload.

      • Apply hypoid gear oil LSD to the rear drive pinion nut and the threads of the differential drive pinion.

  17. ADJUST DIFFERENTIAL DRIVE PINION PRELOAD


    1. A01FIYR

      Using a torque wrench, measure the starting torque of the differential drive pinion.

      Tech Tips


      • The backlash between the differential drive pinion and differential ring gear should allow enough movement of the differential drive pinion to allow this measurement to be performed.

      • Make sure not to include the preload of the differential ring gear (rear differential case sub-assembly) in the measurement of the differential drive pinion preload.

      Differential Drive Pinion Preload (at Starting)
      Item Specified Condition
      New rear drive pinion tapered roller bearing 1.87 to 2.24 N*m (19.07 to 22.84 kgf*cm, 16.55 to 19.83 in.*lbf)
      Reused rear drive pinion tapered roller bearing 1.87 to 2.17 N*m (19.07 to 22.13 kgf*cm, 16.55 to 19.21 in.*lbf)

      • If the preload is less than the specified minimum value, check the preload while retightening the rear drive pinion nut by 5 to 10° to adjust it so that it is within the specified range.

        Torque
        337 N*m (3444 kgf*cm, 249 ft.*lbf) or less

      • If the preload is less than the specified minimum value even when the tightening torque of the rear drive pinion nut is more than the specified maximum value, loosen the rear drive pinion nut and check that the threads of the rear drive pinion nut and differential drive pinion are not stripped.

      • If the threads are not stripped, replace the rear differential drive pinion bearing spacer. Apply hypoid gear oil LSD to the threads of the differential drive pinion and repeat the procedure.

  18. INSPECT TOTAL PRELOAD


    1. A01FIYR

      Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

      Total Preload (at Starting)
      Specification New Rear Drive Pinion Tapered Roller Bearing Reused Rear Drive Pinion Tapered Roller Bearing
      New differential case bearing 2.26 to 2.91 N*m (23.05 to 29.67 kgf*cm, 20.00 to 25.76 in.*lbf) 2.26 to 2.84 N*m (23.05 to 28.96 kgf*cm, 20.00 to 25.14 in.*lbf)
      Reused differential case bearing 2.17 to 2.80 N*m (22.13 to 28.55 kgf*cm, 19.21 to 24.78 in.*lbf) 2.17 to 2.73 N*m (22.13 to 27.84 kgf*cm, 19.21 to 24.16 in.*lbf)

      If the total preload is not within the specified range, adjust the total preload or perform repairs as necessary.

  19. STAKE REAR DRIVE PINION NUT


    1. A01FEQW

      Using SST and a hammer, stake the rear drive pinion nut.

      SST
      09930-00010

  20. INSTALL REAR DIFFERENTIAL CARRIER COVER


    1. A01FGLSE03
      Text in Illustration
      *a 2 to 3 mm (0.0787 to 0.118 in.)

      Apply seal packing to the rear differential carrier as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing 1281, Three bond 1281 or equivalent

      Note


      • Apply the seal packing in a continuous line, approximately 2 to 3 mm (0.0787 to 0.118 in.) in diameter.

      • Overlap the seal packing at least 10 mm (0.394 in.) at the beginning and end of application.

      • Install the rear differential carrier cover within 3 minutes of application.

    2. A01FISF

      Install the rear differential carrier cover with the 8 bolts and 2 rear differential carrier straight pins.

      Torque:
      47 N*m  { 475 kgf*cm, 34 ft.*lbf }

      Note

      Do not fill the differential with oil or drive the vehicle immediately after installing the differential carrier cover. Leave the vehicle for at least 1 hour. Also, avoid sudden acceleration and deceleration for at least 12 hours after application.

  21. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY

    Click here