VALVE BODY ASSEMBLY INSTALLATION


  1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    1. Install the spring and check ball body.

    2. A01FG4RE04
      Text in Illustration
      *1 Manual Valve Connecting Rod
      *2 Manual Valve Lever Sub-assembly

      Align the groove of the manual valve lever sub-assembly with the manual valve connecting rod.

    3. A01FG01E01

      Install the transmission valve body assembly with the 17 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Each bolt length is indicated below.

      Bolt length:

      Bolt A: 21 mm (0.827 in.)

      Bolt B: 31 mm (1.22 in.)

      Bolt C: 64 mm (2.52 in.)

    4. Install the detent spring and detent spring cover with the bolt.

      Note

      Make sure to install the detent spring so that its roller is perpendicularly aligned to the center of the manual valve lever.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    5. Connect the 9 connectors to the solenoid valves.

    6. Connect the oil pressure switch connector.

    7. Coat a new O-ring with ATF and install it to the ATF temperature sensor.

    8. Install the ATF temperature sensor and lock plate with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  2. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    1. Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.

      Note

      Ensure that the O-ring is not twisted or pinched.

    2. Install the valve body oil strainer assembly to the transmission valve body assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  3. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


    1. A01FG03
      Text in Illustration
      *1 Sleeve
      *2 Automatic Transmission Case Sub-assembly
      *a Correct
      *b Incorrect
      *c Protrusion

      Install the 3 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly.

    2. Install a new automatic transmission oil pan gasket and the automatic transmission oil pan sub-assembly to the automatic transmission case sub-assembly with the 9 bolts.

      Torque:
      7.4 N*m  { 75 kgf*cm, 65 in.*lbf }

      Note


      • A01FDFXE06

      • Make sure that there is no oil or foreign matter on the gasket seal surface and automatic transmission oil pan sub-assembly contact surface.

      • Install the gasket so that there is no slack in the gasket, and that the entire circumference of the seal surface is level.

      • Make sure that the 9 gasket drop prevention protrusions are set on the automatic transmission oil pan sub-assembly.

      • When tightening the automatic transmission oil pan sub-assembly, make sure that the gasket is not pinched between the sleeve of the gasket tightening area and the seal surface of the transmission.

  4. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY


    1. A01FIFZE02
      Text in Illustration
      *1 Nut

      Install the No. 1 exhaust pipe support bracket sub-assembly with the 2 bolts (A), 2 bolts (B) and 2 new nuts.

      Torque:
      for Bolt A
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }
      for Nut
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }

      Tech Tips

      Turn the nuts while holding the bolts.

  5. INSTALL NO. 2 ENGINE UNDER COVER


    1. Install the No. 2 engine under cover with the 4 screws.

  6. INSTALL FRONT SUSPENSION MEMBER BRACE


    1. Install the front suspension member brace with the clip and 4 bolts.

      Torque:
      52 N*m  { 530 kgf*cm, 38 ft.*lbf }

  7. ADD AUTOMATIC TRANSMISSION FLUID

    Click here

  8. RESET MEMORY

    Click here