AUTOMATIC TRANSMISSION SYSTEM, Diagnostic DTC:P2714

DTC Code DTC Name
P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)

DESCRIPTION

Based on signals from the accelerator position sensor and speed sensors (NC3, SP2 and NT), the TCM controls the solenoid valve (SLT) using a predetermined current. As a result, the line pressure is adjusted to a pressure that is appropriate for the throttle angle and engine output. Based on the rotation speed indicated by the transmission speed sensors (NT, NC3 and SP2), the TCM calculates the heat level of the friction material, and detects the slip condition of the clutch, etc.

A01FFHTE01
DTC No.

DTC Detection Condition


  1. Diagnosis Condition

  2. Malfunction Status

  3. Other

 Trouble Area
P2714

  1. ECT is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the vehicle is driven with the shift lever in D (no malfunctions are detected in shift solenoid valve SL1, 2, 3, 4 and 5, SR, SLT, transmission revolution sensors (NT, NC3, SP2), engine coolant temperature sensor, oil temperature sensor, knock control sensor, electronic throttle, or CAN2)

  2. - The engine overruns at engine torque that is above each gear's set engine torque

    - The clutch is judged to be slipping, and friction material is overheated beyond a specified threshold

  3. 2 trip detection logic

  • Shift solenoid valve SL1

  • Shift solenoid valve SL2

  • Shift solenoid valve SL3

  • Shift solenoid valve SL4

  • Shift solenoid valve SL5

  • Shift solenoid valve SLT

  • Valve body assembly

  • Torque converter assembly

  • Automatic transmission assembly

MONITOR DESCRIPTION

The TCM calculates the amount of heat absorbed by the friction material based on the difference in speed (clutch slippage) between the turbine and output shaft. The TCM illuminates the MIL and outputs this DTC when the amount of heat absorption exceeds the specified value.

When the shift solenoid valve SLT remains ON, oil pressure goes down and clutch engagement force decreases.

Note

If driving continues under these conditions, the clutches will burn out and the vehicle will no longer be drivable.

INSPECTION PROCEDURE

Note

Perform registration and/or initialization when parts related to the automatic transmission are replaced Click here.

PROCEDURE


  1. CHECK DTC OUTPUT (IN ADDITION TO DTC P0746, P0771, P0776, P0796, P2714, P2808 AND P2817)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / ECT / Trouble Codes.

    5. Read the DTCs using the GTS.

      Result
      Result Proceed to
      Only DTC P2714 is output A
      P2714 and one or more of the following DTCs are output: P0746, P0771, P0776, P0796, P2808, P2817 B
      P0746, P0771, P0776, P0796, P2714, P2808 or P2817 and other DTCs are output C

      Tech Tips

      If any DTCs other than P0746, P0771, P0776, P0796, P2714, P2808 and P2817 are output, perform troubleshooting for those DTCs first.


    B

    CHECK DTC OUTPUT Click here

    C

    GO TO DTC CHART Click here

    A

  2. INSPECT SHIFT SOLENOID VALVE SLT


    1. A01FI7WE21
      Text in Illustration
      *1 Shift Solenoid Valve SLT

      Remove the shift solenoid valve SLT Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the shift solenoid valve SLT - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a positive (+) battery lead with a 21 W bulb to terminal 2 and a negative (-) battery lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.

    NG

    REPLACE SHIFT SOLENOID VALVE SLT Click here

    OK

  3. INSPECT TRANSMISSION VALVE BODY ASSEMBLY


    1. Check the transmission valve body assembly Click here.

      OK
      There is no foreign matter on each valve and they operate smoothly.

    NG

    REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY Click here

    OK

  4. INSPECT TORQUE CONVERTER ASSEMBLY


    1. Check the torque converter assembly Click here.

      OK
      The torque converter operates normally.

    NG

    REPLACE TORQUE CONVERTER ASSEMBLY Click here

    OK

    REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY Click here

  5. CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / ECT / Trouble Codes.

    5. Check if DTCs other than P2714 are output.

      Result
      Result Proceed to
      P2714 and P0746 are output A

      • P2714, P0771 and P0776 are output

      • P2714 and P0776 are output

      		 B

      • P2714, P0771 and P0796 are output

      • P2714 and P0776 are output

      • P2714, P0796 and P2808 are output

      		 C
      P2714 and P2808 are output D
      P2714 and P2817 are output E

    B

    GO TO DTC P0776 FLOWCHART Click here

    C

    GO TO DTC P0796 FLOWCHART Click here

    D

    GO TO DTC P2808 FLOWCHART Click here

    E

    GO TO DTC P2817 FLOWCHART Click here

    A

    GO TO DTC P0746 FLOWCHART Click here