VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1281

DTC Code DTC Name
C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)

DESCRIPTION

DTC C1281 will be cleared when the master cylinder pressure sensor sends a master cylinder pressure signal or when Test Mode ends. DTC C1281 is output only in Test Mode.

DTC Code DTC Detection Condition Trouble Area
C1281 Detected only during Test Mode.

  • Stop light switch

  • Harness or connector

  • Brake pedal load sensing switch (Brake pedal support assembly)

  • Master cylinder pressure sensor (Brake actuator assembly)

WIRING DIAGRAM

Refer to DTCs C1425 and C1429 Click here, or Click here.

INSPECTION PROCEDURE

Note

When replacing the brake actuator assembly, perform zero point calibration and store system information Click here.

PROCEDURE


  1. CHECK STOP LIGHT OPERATION


    1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

      OK
      Condition Illumination Condition
      Brake pedal depressed ON
      Brake pedal released OFF

    NG

    INSPECT STOP LIGHT CIRCUIT Click here

    OK

  2. READ VALUE USING GTS (STOP LIGHT SW/BRAKE PEDAL LOAD SENSING SW)


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      Brake Pedal Load Sensing SW Brake pedal load sensing switch / ON or OFF

      ON: Brake pedal depressed beyond the specified point

      OFF: Brake pedal not depressed beyond the specified point

      		 -

    6. Check that the stop light switch display and brake pedal load sensing switch display observed on the GTS change according to brake pedal operation.

      OK
      The GTS displays ON or OFF according to brake pedal operation.

    7. Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn ON.

      OK
      First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.
      Result
      Result Proceed to
      OK A
      NG (Turning on of the stop light switch is not confirmed) B
      NG (Turning on of the brake pedal load sensing switch is not confirmed) C
      NG (The brake pedal load sensing switch turns on first) D

    B

    Click here

    C

    CHECK HARNESS AND CONNECTOR (FSW+ TERMINAL) Click here

    D

    CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION Click here

    A

  3. READ VALUE USING GTS (MASTER CYLINDER SENSOR)


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Master Cylinder Sensor Master cylinder pressure sensor / min.: 0.00 V, max.: 5.00 V When brake pedal is released: 0.3 to 0.9 V The value increases when the brake pedal is depressed.

    6. Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the GTS changes when the brake pedal is depressed.

      OK
      When the pedal is depressed, voltage displayed on the GTS increases.

    NG

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    OK

  4. PERFORM TEST MODE (SIGNAL CHECK)


    1. Turn the engine switch off.

    2. Perform the sensor check in the Test Mode procedure Click here.

      OK
      All Test Mode DTCs are cleared.

    NG

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    OK

    CHECK FOR INTERMITTENT PROBLEMS Click here

  5. CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. A01FH1RE04
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU [Brake Actuator Assembly])

      Turn the engine switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    3. Disconnect the skid control ECU (brake actuator assembly) connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A13-2 (STP) - Body ground Brake pedal depressed 8 to 14 V
      Brake pedal released Below 1.5 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  6. CHECK HARNESS AND CONNECTOR (FSW+ TERMINAL)


    1. A01FGCKE99
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU [Brake Actuator Assembly])

      Turn the engine switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the skid control ECU (brake actuator assembly) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A13-27 (FSW+) - Body ground Brake pedal depressed 950 to 1050 Ω
      Brake pedal released 203 to 223 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  7. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION


    1. Turn the engine switch off.

    2. Check the brake pedal height and stop light switch installation Click here.

      OK
      The brake pedal height and stop light switch installation are normal.

    NG

    ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH Click here

    OK

    REPLACE BRAKE PEDAL SUPPORT ASSEMBLY Click here