REAR BUMPER REASSEMBLY


  1. INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY


    1. A01EWE1

      Install the rear bumper reinforcement sub-assembly with the 6 nuts.

      Torque:
      61 N*m  { 622 kgf*cm, 45 ft.*lbf }

  2. INSTALL WHEEL HOUSE REINFORCEMENT LH


    1. A01ETDT

      Engage the clip.

    2. Install the wheel house reinforcement LH with the screw and nut.

  3. INSTALL WHEEL HOUSE REINFORCEMENT RH

    Tech Tips

    Use the same procedure as for the LH side.

  4. INSTALL REAR BUMPER SIDE RETAINER LH


    1. A01EZ0V

      Engage the 6 claws.

    2. Install the rear bumper side retainer LH with the 3 screws.

      Torque:
      3.0 N*m  { 31 kgf*cm, 27 in.*lbf }

  5. INSTALL REAR BUMPER SIDE RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  6. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)


    1. A01EU6KE01
      Text in Illustration
      *A LH Side
      *B RH Side
      *a Keyhole
      *b Snap

      Engage the 2 claws to install the No. 1 ultrasonic sensor retainer to the rear bumper assembly.

      Note


      • Do not damage the front bumper with the protrusion when installing the retainer.

      • Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the front bumper.

      Tech Tips

      When installing the retainer, align the keyhole and snap as shown in the illustration.

  7. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)


    1. A01EVBZE01
      Text in Illustration
      *A LH Side
      *B RH Side

      Engage the 2 claws to install the No. 1 ultrasonic sensor to the No. 1 ultrasonic sensor retainer.

      Note

      Push the No. 1 ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the ultrasonic sensor.

  8. INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)


    1. A01EYP4E01
      Text in Illustration
      *A LH Side
      *B RH Side

      Engage the 4 claws to install the ultrasonic sensor clip.

    2. A01ETTEE01
      Text in Illustration
      *A LH Side
      *B RH Side

      Engage the clamp.

    3. Connect the connector.

  9. INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)


    1. A01EUOS

      Connect the 4 connectors.

    2. Engage the 4 clamps to install the No. 2 luggage room wire.

  10. INSTALL REFLEX REFLECTOR ASSEMBLY LH


    1. A01EYRA

      Engage the guide.

    2. Install the reflex reflector assembly LH with the screw.

  11. INSTALL REFLEX REFLECTOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. INSTALL REAR BUMPER PAD LH


    1. Wipe off any tape adhesive residue with cleaner.

    2. A01ETDS

      Install a new rear bumper pad LH.

      Tech Tips

      Stick the new rear bumper pad LH on the line marked on the rear bumper assembly.

  13. INSTALL REAR BUMPER PAD RH


    1. Wipe off any tape adhesive residue with cleaner.

    2. A01ETU7

      Install a new rear bumper pad RH.

      Tech Tips

      Stick the new rear bumper pad RH on the line marked on the rear bumper assembly.