HAZARD WARNING SWITCH REMOVAL


  1. PRECAUTION

    Note

    After turning the Ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Navigation System)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT PANEL GARNISH LH


    1. A01EXDU

      Disengage the 3 clips and 8 guides to remove the front panel garnish LH as shown in the illustration.

  4. REMOVE FRONT PANEL GARNISH RH


    1. A01EYBQ

      Disengage the 3 clips and 8 guides to remove the front panel garnish RH.

  5. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01ETO0

      Using a moulding remover, pry up on the center instrument cluster finish panel sub-assembly until there is enough of a gap to make it possible to pull on the panel by hand.

    2. A01EVW2

      Pull the center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 7 clips and 2 guides to remove the center instrument cluster finish panel sub-assembly as shown in the illustration.

  6. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01EUQP

      Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 4 clips as shown in the illustration.

    2. Disconnect the connector to remove the No. 2 instrument panel register assembly.

  7. REMOVE FRONT CONSOLE UPPER PANEL GARNISH


    1. for Blank Type:


      1. A01EVN1

        Disengage the 2 claws and remove the front console upper panel garnish as shown in the illustration.

    2. for 3 Switch Hole Type:


      1. A01EY7R

        Disengage the 2 claws as shown in the illustration.

      2. Disconnect the each connector to remove the front console upper panel garnish.

  8. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)


    1. A01EXQHE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01EXK8

      Remove the 4 bolts.

    3. A01EU7P

      Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

    4. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.

  9. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)


    1. A01EU97E01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01EWLR

      Remove the 4 bolts.

    3. A01EW14

      Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

    4. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.

  10. REMOVE NO. 1 RADIO BRACKET (w/o Navigation System)


    1. A01EVJD

      Remove the 5 screws and No. 1 radio bracket.

  11. REMOVE NO. 2 RADIO BRACKET (w/o Navigation System)


    1. A01ETVH

      Remove the 5 screws and No. 2 radio bracket.

  12. REMOVE NO. 1 RADIO RECEIVER BRACKET (w/ Navigation System)


    1. A01EYTS

      Remove the 5 screws and No. 1 radio receiver bracket.

  13. REMOVE NO. 2 RADIO RECEIVER BRACKET (w/ Navigation System)


    1. A01EXPF

      Remove the 5 screws and No. 2 radio receiver bracket.

  14. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (HAZARD SWITCH)


    1. A01EV9M

      Disengage the 4 clips and guide, and remove the air conditioning control assembly as shown in the illustration.

  15. REMOVE AIR CONDITIONING PANEL SUB-ASSEMBLY


    1. A01EY71

      Remove the 2 screws.

    2. A01EWKK

      Disengage the 7 claws and remove the air conditioner panel sub-assembly.

  16. REMOVE HEATER CONTROL HOUSING SUB-ASSEMBLY


    1. A01EUUV

      Remove the 3 screws.

    2. Disengage the 4 claws and remove the heater control retainer RH from the heater control housing sub-assembly.

  17. REMOVE HEATER CONTROL SWITCH BOARD

    Note

    When disassembling the air conditioning control assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.


    1. A01EUPD

      Remove the 5 screws and heater control switch board.