FRONT SEAT SIDE AIRBAG ASSEMBLY INSTALLATION


  1. INSTALL FRONT SEAT AIRBAG ASSEMBLY

    CAUTION:


    • The nuts must not be reused.

    • Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.


    1. Install the front seat airbag assembly with 2 new nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Engage the 2 clamps.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)


    1. Temporarily install the separate type front seatback cover with pad.

    2. Engage the 4 claws to install the 2 front seat headrest supports.

    3. Install the 2 brackets with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Install the bracket securely.

    4. A01EX62

      Turn back the separate type front seatback cover.

    5. Using hog ring pliers, install the 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    6. A01ET1G

      Using hog ring pliers, install 3 new hog rings.

    7. A01EYWZ

      Using hog ring pliers, install 5 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)


    1. Temporarily install the separate type front seatback cover with pad.

    2. Engage the 4 claws to install the 2 front seat headrest supports.

    3. Install the 2 brackets with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Install the bracket securely.

    4. A01EX62

      Turn back the separate type front seatback cover.

    5. Using hog ring pliers, install the 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    6. A01EY2O

      Using hog ring pliers, install 3 new hog rings.

      Note

      When installing the hog rings, take care to minimize wrinkles as much as possible.

    7. A01EUTJ

      Using hog ring pliers, install 5 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  4. CONNECT AIRBAG WIRE HARNESS (for Manual Seat)


    1. Engage the claw and 3 clamps to connect the airbag wire harness.

    2. Engage the fastener to install the airbag wire harness.

    3. Connect the rubber band of the separate type front seatback cover with pad.

  5. CONNECT AIRBAG WIRE HARNESS (for Power Seat)


    1. w/ Seat Heater System:


      1. Engage the clamp.

      2. Connect the connector.

    2. Engage the claw and 3 clamps to connect the airbag wire harness.

    3. Engage the fastener to install the airbag wire harness.

    4. Connect the rubber band of the separate type front seatback cover with pad.

  6. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)

    Click here

  7. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)

    Click here

  8. PERFORM DIAGNOSTIC SYSTEM CHECK

    for Separate Type Yaw Rate Sensor: Click here

    for Built-in Type Yaw Rate Sensor: Click here