REAR DOOR LOCK INSTALLATION

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.


  1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A01EYUX

      Install the rear door inside locking cable assembly.

    2. A01EUR1

      Engage the 3 claws.

  2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A01EU9A

      Install the rear door lock remote control cable assembly.

    2. A01EVM0

      Engage the claw.

  3. INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

    Note


    • When reusing the removed rear door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door with motor lock assembly.


    1. Apply MP grease to the sliding parts of the rear door lock with motor assembly.

    2. When reusing the rear door with motor lock assembly:


      1. A01EYG3

        Install a new door lock wiring harness seal to the rear door lock with motor assembly.

    3. A01EVXJE01
      Text in Illustration
      *1 Release Plate

      Insert the rear door lock with motor assembly to the rear door outside handle release plate, and set it to the rear door panel.

    4. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock with motor assembly.

    5. Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A01ETPG

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  5. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. A01EWEY

      Install the rear door quarter window glass in the direction indicated by the arrow in the illustration.

  6. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. A01EVGG

      Install the rear door lower window frame sub-assembly with the screw and 2 bolts.

  7. INSTALL REAR DOOR GLASS RUN


    1. A01ETSR

      Install the rear door glass run.

  8. INSTALL REAR DOOR WEATHERSTRIP


    1. A01EXAC

      Install the upper part of rear door weatherstrip as shown in the illustration.

  9. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the rear door panel.

    2. A01EXSNE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the connector.

  10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A01EW36

      Install the rear door inner glass weatherstrip.

  11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01EWKA

      Install the No. 1 door scuff plate clamp as shown in the illustration.

    2. A01EY4QE01
      Text in Illustration
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    3. Connect the connector.

    4. A01EYELE01
      Text in Illustration
      *1 Reference Boss

      Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.

    5. A01EXGD

      Engage the 8 clips and install the rear door trim board sub-assembly.

    6. Install the 3 screws.

    7. If protective tape has been applied, remove it.

  12. INSTALL REAR ARMREST ASSEMBLY


    1. A01EYTY

      Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.

  13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A01EWWS

      Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

  14. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01ET39

      Engage the 3 claws to install the rear door inside handle bezel plug.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  17. CHECK POWER WINDOW CONTROL SYSTEM

    Click here