CLEARANCE WARNING ECU REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01EXKX

      Disconnect the front door opening trim weatherstrip RH.

  6. REMOVE INSTRUMENT SIDE PANEL RH


    1. A01EWKD

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01EYQ9

      Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.

  7. REMOVE FRONT PANEL GARNISH RH


    1. A01EYBQ

      Disengage the 3 clips and 8 guides to remove the front panel garnish RH.

  8. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. A01ETM9

      Disengage the 4 claws.

    2. Disengage the 2 guides.

    3. Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.

  9. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)


    1. A01EY0O

      Remove the bolt <B> and screw <C>.

    2. Open the lower instrument panel door.

    3. A01ET98

      Remove the 3 screws <C>.

    4. A01ETI0

      Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.

  10. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)


    1. A01EYL2

      Disengage the 2 claws and 4 clips to remove the upper instrument panel finish panel as shown in the illustration.

    2. w/ Smart Entry and Start System:


      1. Disconnect the connector.

  11. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for RHD)


    1. A01EXTH

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  12. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)


    1. A01ETM3

      Remove the 2 bolts <B>.

    2. w/o Driver Side Knee Airbag:


      1. A01EVFO

        Disengage the 5 clips and 3 guides to remove the instrument panel sub-assembly.

    3. w/ Driver Side Knee Airbag:


      1. A01EVDY

        Disengage the 4 claws, 7 clips and 3 guides to remove the instrument panel sub-assembly.

  13. REMOVE ECU INTEGRATION BOX RH


    1. for LHD:


      1. Disconnect each connector.

      2. A01EWHE

        Remove the bolt, 2 nuts and ECU integration box RH.

    2. for RHD:


      1. Disconnect each connector.

      2. A01EYM0

        Remove the bolt, 2 nuts and ECU integration box RH.

  14. REMOVE CLEARANCE WARNING ECU ASSEMBLY


    1. for LHD:


      1. A01EYKD

        Disengage the 2 claws and remove the clearance warning ECU assembly.

    2. for RHD:


      1. A01EYCL

        Disengage the 2 claws and remove the clearance warning ECU assembly.