NAVIGATION SYSTEM (for Navigation Receiver Type) Microphone Circuit between Microphone and Navigation Receiver Assembly

DESCRIPTION

The navigation receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the navigation receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the navigation receiver assembly.

WIRING DIAGRAM

A01EVRJE02

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK MICROPHONE (OPERATION CHECK)


    1. A01EUS1

      Enter the "Microphone Check" screen.

      Refer to Check Microphone in Operation Check Click here.

    2. When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

    3. Push the recording switch and perform voice recording.

      Tech Tips


      • Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

      • Voice can be recorded for up to 5 seconds.

    4. Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.

      OK
      All check results are normal.

    NG

    CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)) Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))


    1. Disconnect the I67 navigation receiver assembly connector.

    2. Disconnect the S7 roof console box assembly (telephone microphone assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I67-4 (MACC) - S7-14 (MACC) Always Below 1 Ω
      I67-5 (MIN+) - S7-13 (MCO+) Always Below 1 Ω
      I67-19 (MIN-) - S7-12 (MCO-) Always Below 1 Ω
      I67-6 (SNS2) - S7-15 (SNS2) Always Below 1 Ω
      I67-4 (MACC) - Body ground Always 10 kΩ or higher
      I67-5 (MIN+) - Body ground Always 10 kΩ or higher
      I67-19 (MIN-) - Body ground Always 10 kΩ or higher
      I67-18 (SGND) - Body ground Always 10 kΩ or higher
      I67-6 (SNS2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT NAVIGATION RECEIVER ASSEMBLY


    1. A01ETPNE11
      Text in Illustration
      *a

      Component with harness connected

      (Navigation Receiver Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I67-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I67-18 (SGND) - Body ground Always Below 1 Ω
      I67-19 (MIN-) - Body ground Always Below 1 Ω

    3. Proceed to the next step based on the inspection result.

      Result
      Result Proceed to
      NG A
      OK B

    B

    INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) Click here

    A

    REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

  4. INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    1. Remove the roof console box assembly (telephone microphone assembly) Click here.

    2. A01ETPAE59
      Text in Illustration
      *a

      Component without harness connected

      (Roof Console Box Assembly (Telephone Microphone Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      15 (SNS2) - 12 (MCO-) Always Below 1 Ω

    NG

    REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) Click here

    OK

  5. INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    1. Turn the ignition switch to ACC.

    2. A01ETHDE48
      Text in Illustration
      *a

      Component with harness connected

      (Roof Console Box Assembly (Telephone Microphone Assembly))

      Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S7 roof console box assembly (telephone microphone assembly) connector.

    3. Check the waveform of the roof console box assembly (telephone microphone assembly) using the oscilloscope.

      Result
      Result Proceed to
      A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output. A
      A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output. B

    B

    REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) Click here

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here