NOISE FILTER REMOVAL


  1. PRECAUTION (w/ Rear Seat Side Airbag)

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)


    1. A01EYIPE01

      Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

      2. Repeat the step above for the other hook.

    2. Remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  4. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)


    1. A01EZ1N

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the LH side and RH side.

  5. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.

    2. A01EY53

      Remove the bolt.

    3. Disengage the hook and remove the rear side seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  6. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)


    1. A01EWH4E01

      Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

      2. Repeat the step above for the other hook.

    2. w/ Seat Heater System:


      1. Disconnect the 2 seat heater connectors.

    3. Remove the rear seat cushion assembly.

  7. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    1. A01EZ1N

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  8. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

  9. REMOVE REAR SEATBACK COVER (for Reclining Seat Type)


    1. A01EUWN

      Disengage the 4 claws and remove the 2 rear seatback covers.

      Tech Tips

      Use the same procedure as for the LH side.

  10. REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)


    1. w/ Rear Seat Side Airbag:


      1. Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.

    2. Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.

    3. A01EVHV

      Disengage the 2 hooks and disconnect the cover.

    4. Remove the 2 nuts, 2 bolts and rear seatback assembly LH.

  11. REMOVE REAR DOOR SCUFF PLATE LH (for Reclining Seat Type)


    1. A01EWHQ

      Disengage the 6 claws and remove the rear door scuff plate LH.

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Reclining Seat Type)


    1. Disconnect the rear door opening trim weatherstrip LH.

  13. REMOVE REAR SEAT SIDE GARNISH LH (for Reclining Seat Type)


    1. A01EY25

      Remove the bolt.

    2. Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.

  14. REMOVE RADIO SETTING CONDENSER (for High Mounted Stop Light)

    Note

    When the terminal covers are removed, the radio setting condenser must be replaced because the terminal covers and condenser are supplied as a set.


    1. A01EUUZ

      Remove the bolt.

    2. Disengage the clamp and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. A01ETIY

      Disengage the claw and pull out the cover as shown in the illustration.

    4. A01EUQ4

      Using a screwdriver, disengage the 6 claws and remove the 2 terminal covers with wire harness from the condenser.

    5. A01EYBE

      Using a screwdriver, bend back and break off the claw as shown in the illustration.

    6. Remove the terminal cover from the wire harness.

      Note


      • Make sure to hold the wire harness on the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

      • Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

      • Check for deformation of the terminal after the wire harness has been removed from the terminal cover.

  15. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Window Defogger)

    for Fold Down Seat Type: Click here

  16. REMOVE ROOF SIDE INNER GARNISH LH (for Window Defogger)


    1. A01EXPK

      Disengage the 5 clips.

    2. Disengage the guide and remove the roof side inner garnish LH.

  17. REMOVE RADIO SETTING CONDENSER (for Window Defogger)

    Note

    When the terminal cover is removed, the radio setting condenser must be replaced because the terminal cover and condenser are supplied as a set.


    1. A01EYJ8

      Remove the bolt.

    2. Disengage the 2 clamps and disconnect the radio setting condenser with wire harness from the vehicle body.

    3. A01EUEI

      Using a screwdriver, disengage the 3 claws and remove the terminal cover with wire harness from the condenser.

    4. A01EXF2

      Using a screwdriver, bend back and break off the claw as shown in the illustration.

    5. Remove the terminal cover from the wire harness.

      Note


      • Make sure to hold the wire harness on the crimping side of the terminal when disconnecting the wire harness from the terminal cover.

      • Make sure not to bend the exposed wire when disconnecting the wire harness from the terminal cover.

      • Check for deformation of the terminal after the wire harness has been removed from the terminal cover.