WIPER SWITCH INSTALLATION


  1. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY


    1. A01ETGD

      Engage the claw to install the windshield wiper switch assembly as shown in the illustration.

    2. Connect each connector.

  2. INSTALL UPPER STEERING COLUMN COVER


    1. Engage the 2 claws to install the upper steering column cover.

    2. Engage the 4 clips and 2 guides to install the instrument cluster finish panel to the upper steering column cover.

  3. INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)


    1. Engage the 2 claws.

    2. install the screw.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

    3. Turn the steering wheel assembly to the left and install the screw.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

    4. Turn the steering wheel assembly to the right and install the lower steering column cover with the screw.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

  4. INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Note

    If the lower steering column cover is installed in the incorrect order, it will not be possible to assemble the steering column cover.


    1. Engage the 2 claws.

    2. A01EWMT

      Engage the 2 claws.

      Tech Tips

      Press the area around the claws to engage them.

    3. Turn the steering wheel assembly to the left and install the screw.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

    4. Turn the steering wheel assembly to the right and install the lower steering column cover with the screw.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

  5. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)


    1. w/o Driver Side Knee Airbag:


      1. Engage the 5 clips and 3 guides.

    2. w/ Driver Side Knee Airbag:


      1. Engage the 4 claws, 7 clips and 3 guides.

    3. Install the instrument panel sub-assembly with the 2 bolts <B>.

  6. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)


    1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

  7. INSTALL FRONT PANEL GARNISH LH (for Power Tilt and Power Telescopic Steering Column)


    1. A01ETI1

      Engage the 3 clips and 8 guides to install the front panel garnish LH.

  8. INSTALL INSTRUMENT SIDE PANEL LH (for Power Tilt and Power Telescopic Steering Column)


    1. Engage the 3 guides.

    2. A01ETDE

      Engage the 4 claws to install the instrument side panel LH as shown in the illustration.

  9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Power Tilt and Power Telescopic Steering Column)


    1. A01EWEQE01
      Text in Illustration
      *1 Alignment Mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  10. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for Power Tilt and Power Telescopic Steering Column)


    1. Engage the 2 clips.

    2. Install the cowl side trim sub-assembly LH with the clip.

  11. INSTALL FRONT DOOR SCUFF PLATE LH (for Power Tilt and Power Telescopic Steering Column)


    1. Engage the 10 claws to install the front door scuff plate LH.

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)

    Note


    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    • Reset the auto tilt away function setting to the previous condition by changing the customize parameter Click here.