PARKING BRAKE PEDAL (for RHD) REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

  4. REMOVE FRONT WHEEL RH

  5. REMOVE SHIFT LEVER SUPPORT

    Tech Tips

    Use the same procedure as for the LH side Click here.

  6. REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY


    1. A01EW4U

      Disengage the clamp.

    2. Remove the bolt.

    3. Disconnect the connector and remove the No. 1 indoor electrical key antenna assembly.

      Note

      Be careful when removing the indoor electrical key antenna assembly. If the antenna is dropped, replace it with a new one.

  7. REMOVE FLOOR CARPET BRACKET RH


    1. A01ET17

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket RH.

  8. REMOVE AIRBAG SENSOR ASSEMBLY


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Turn back the carpet.

    4. A01EVT2

      Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    5. Remove the 3 bolts and airbag sensor assembly.

  9. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL


    1. A01EYL2

      Disengage the 2 claws and 4 clips to remove the upper instrument panel finish panel as shown in the illustration.

    2. w/ Smart Entry and Start System:


      1. Disconnect the connector.

  10. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

    Tech Tips

    Use the same procedure as for the LH side Click here.

  11. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. for Manual Tilt and Manual Telescopic Steering Column:


      1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.

    2. A01EVKJ

      Using a moulding remover, disengage the 4 clips and 2 guides.

    3. for LHD:


      1. A01EYAO

        Disengage the 3 claws, 7 clips and 4 guides.

    4. for RHD:


      1. A01EUS4

        Disengage the 4 claws, 5 clips and 4 guides as shown in the illustration.

    5. Disconnect each connector.

    6. A01EWRI

      Remove the instrument cluster finish panel assembly as shown in the illustration.

  12. REMOVE COMBINATION METER ASSEMBLY

    Tech Tips

    Use the same procedure as for the LH side Click here.

  13. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY


    1. A01EU2G

      Disconnect the connector from the footwell light.

    2. Remove the bolt.

    3. Disengage the 2 claws to remove the No. 2 air duct sub-assembly.

  14. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

    Tech Tips

    Use the same procedure as for the LH side Click here.

  15. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

    Tech Tips

    Use the same procedure as for the LH side Click here.

  16. LOOSEN ADJUSTING NUT


    1. A01EUCNE01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Remove the lock nut and loosen the adjusting nut.

  17. SEPARATE NO. 4 PARKING BRAKE CABLE ASSEMBLY


    1. A01EW27E01
      Text in Illustration
      *a Turn
      *b Hold

      Separate the No. 4 parking brake cable assembly from the parking brake control pedal assembly as shown in the illustration.

  18. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. A01EVDH

      Remove the clip from the No. 1 parking brake cable assembly.

    2. Remove the bolt and separate the No. 1 parking brake cable assembly.

    3. A01ETO2

      Disconnect the parking brake switch connector.

    4. A01ESPC

      Remove the bolt, 2 nuts and parking brake control pedal assembly.