PARKING BRAKE PEDAL (for LHD) REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE SHIFT LEVER SUPPORT


  4. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

    CAUTION:

    When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01ETJU

      Remove the 4 bolts.

    4. Disengage the 2 claws to disconnect the DLC3.

    5. A01EW0W

      Disengage the 2 hooks to remove the lower No. 1 instrument panel airbag assembly.

      Note

      When removing the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.

    6. A01ETZ9E01
      Text in Illustration
      *1 Protective Tape
      *2 Airbag Connector
      *3 Airbag Connector Lock

      Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.

    7. Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  5. REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (w/ Smart Entry and Start System)


    1. A01EW4U

      Disengage the clamp.

    2. Remove the bolt.

    3. Disconnect the connector and remove the No. 1 indoor electrical key antenna assembly.

      Note

      Be careful when removing the indoor electrical key antenna assembly. If the antenna is dropped, replace it with a new one.

  6. REMOVE FLOOR CARPET BRACKET RH


    1. A01ET17

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket RH.

  7. REMOVE AIRBAG SENSOR ASSEMBLY


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Turn back the carpet.

    4. A01EVT2

      Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    5. Remove the 3 bolts and airbag sensor assembly.

  8. LOOSEN ADJUSTING NUT


    1. A01EUS6E01
      Text in Illustration
      *1 Lock Nut
      *2 Adjusting Nut

      Remove the lock nut and loosen the adjusting nut.

  9. SEPARATE NO. 4 PARKING BRAKE CABLE ASSEMBLY


    1. A01EW27E01
      Text in Illustration
      *a Turn
      *b Hold

      Separate the No. 4 parking brake cable assembly from the parking brake control pedal assembly as shown in the illustration.

  10. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. Turn back the floor carpet.

    2. A01EWLH

      Remove the clip from the No. 1 parking brake cable assembly.

    3. Remove the bolt and 2 nuts, and separate the No. 1 parking brake cable assembly.

    4. A01EUB7

      Disconnect the parking brake switch connector.

    5. A01ESZH

      Remove the bolt, 2 nuts and parking brake control pedal assembly.