VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1430, C1431

DTC Code DTC Name
C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction
C1431 Brake Pedal Load Sensing Switch ON Stuck Malfunction

DESCRIPTION

The brake pedal load sensing switch turns on when the brake pedal is depressed with a force exceeding a predetermined level.

The skid control ECU uses this circuit to detect if the brake pedal is depressed or not.

DTC No. DTC Detection Condition Trouble Area
C1430

Either of the following is detected:


  1. With the stop light switch on, the brake pedal load sensing switch off, the master cylinder pressure more than 6 MPa (61.2 kgf/cm2, 870 psi), the vehicle acceleration rate is less than -4 m/s2for 1 second or more.

  2. With the stop light switch on, the brake pedal load sensing switch off, and master cylinder pressure more than 6 MPa (61.2 kgf/cm2, 870 psi), the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.

  • Brake pedal load sensing switch (Brake pedal support assembly)

  • Brake pedal load sensing switch circuit
C1431

Either of the following is detected:


  1. With the stop light switch off, the brake pedal load sensing switch on, the master cylinder pressure less than 0.7 MPa (7.13 kgf/cm2, 101 psi), the vehicle acceleration rate is more than -0.8 m/s2for 10 seconds or more. (Only when the engine is running and booster malfunctions are not detected.)

  2. The condition that the brake pedal load sensing switch remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (19 mph) occurs 5 times in succession.

  • Brake pedal load sensing switch (Brake pedal support assembly)

  • Brake pedal load sensing switch circuit

WIRING DIAGRAM

Refer to DTC C1429 Click here.

INSPECTION PROCEDURE

Tech Tips

When C1249, C1425 and/or C1426 is output together with C1430 and/or C1431, inspect and repair the trouble areas indicated by C1249, C1425 and/or C1426 first Click here, Click here, and/or Click here.

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Select the Data List using the intelligent tester Click here.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      Brake Pedal Load Sensing SW Brake pedal load sensing switch / ON or OFF

      ON: Brake pedal depressed beyond a specified point

      OFF: Brake pedal not depressed beyond a specified point

      		 -

    4. Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.

      OK
      The intelligent tester displays on or off according to brake pedal operation.

    5. Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn on.

      OK
      First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.
      Result
      Result Proceed to
      OK A
      NG (Turning on of the brake pedal load sensing switch is not confirmed.) B
      NG (The brake pedal load sensing switch turns on first.) C

    B

    INSPECT BRAKE PEDAL LOAD SENSING SWITCH Click here

    C

    CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION Click here

    A

  2. RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Clear the DTCs Click here.

    3. Turn the ignition switch off.

    4. Start the engine.

    5. Perform a road test.

    6. Check if the same DTC is output Click here.

      Result
      Result Proceed to
      DTCs C1430 and C1431 are not output. A
      DTCs C1430 and/or C1431 are output. B

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

  3. INSPECT BRAKE PEDAL LOAD SENSING SWITCH


    1. A01EYX7E01
      Text in Illustration
      *a

      Component without harness connected

      (Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))

      Turn the ignition switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the brake pedal load sensing switch connector.

      Note


      • Do not remove the brake pedal load sensing switch from the brake pedal support assembly.

      • When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      2 (FSW+) - 1 (FSW-)

      Switch OFF

      (Brake pedal depressed)

      		 950 to 1050 Ω
      2 (FSW+) - 1 (FSW-)

      Switch ON

      (Brake pedal released)

      		 203 to 223 Ω
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    B

    REPLACE BRAKE PEDAL SUPPORT ASSEMBLY Click here

    C

    REPLACE BRAKE PEDAL SUPPORT ASSEMBLY Click here

    A

  4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the skid control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A49-34 (FSW+) - A40-2 (FSW+) Always Below 1 Ω
      A49-34 (FSW+) - Body ground Always 10 kΩ or higher
      A40-1 (FSW-) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  5. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION


    1. Turn the ignition switch off.

    2. Check the brake pedal height and stop light switch assembly installation Click here for LHD or Click here for RHD).

      OK
      The brake pedal height and stop light switch assembly installation are normal.
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG (for LHD) C
      NG (for RHD) D

    B

    REPLACE BRAKE PEDAL SUPPORT ASSEMBLY Click here

    C

    ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY Click here

    D

    ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY Click here

    A

    REPLACE BRAKE PEDAL SUPPORT ASSEMBLY Click here