VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1249

DTC Code DTC Name
C1249 Open in Stop Light Switch Circuit

DESCRIPTION

The skid control ECU receives stop light switch signals and uses them to determine whether or not the brakes are applied.

DTCs may be stored if one of the following occurs:


Tech Tips

*: The skid control ECU may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.

DTC No. DTC Detection Condition Trouble Area
C1249

The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, the master cylinder pressure is 0.5 MPa (5.09 kgf/cm2, 72 psi) or less, and the stop light switch is on for 60 seconds or more.

  • STOP fuse

  • Stop light switch assembly

  • Stop light switch circuit

  • Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM

A01EY8KE03

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK ACCELERATOR PEDAL AND BRAKE PEDAL OPERATION


    1. Interview the customer to check if the pedals were depressed simultaneously while driving or braking.

      OK
      The pedals were not depressed simultaneously.

      Tech Tips

      The skid control ECU may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously.

      If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.


    NG

    END

    OK

  2. CHECK STOP LIGHT OPERATION


    1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

      OK
      Condition Illumination Condition
      Brake pedal depressed. ON
      Brake pedal released. OFF

    NG

    CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL) Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Select the Data List using the intelligent tester Click here.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -

    4. Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

      OK
      The intelligent tester displays on or off according to brake pedal operation.

    NG

    CHECK HARNESS AND CONNECTOR (STP TERMINAL) Click here

    OK

  4. RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Clear the DTCs Click here.

    3. Turn the ignition switch off.

    4. Start the engine.

    5. Drive the vehicle and depress the brake pedal several times to test the stop light circuit.

    6. Check if the same DTC is output Click here.

      Result
      Result Proceed to
      DTC C1249 is not output. A
      DTC C1249 is output. B

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts Click here.


    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

  5. CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    1. A01EVRXE10
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Check that the STOP (7.5 A) fuse is normal.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the stop light switch assembly connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A33-2 - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

    OK

  6. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. A01EWH3E01
      Text in Illustration
      *a

      Component without harness connected

      (Stop Light Switch Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Switch pin free Below 1 Ω
      1 - 2 Switch pin pushed in 10 kΩ or higher

    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. A01EXFAE13
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Reconnect the stop light switch assembly connector.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the skid control ECU connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A49-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
      A49-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V

      Tech Tips

      *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

    OK

  8. RECONFIRM DTC


    1. Reconnect the skid control ECU connector.

    2. Clear the DTCs Click here.

    3. Turn the ignition switch off.

    4. Start the engine.

    5. Drive the vehicle and depress the brake pedal several times to test the stop light circuit.

    6. Check if the same DTC is output Click here.

      Result
      Result Proceed to
      DTC C1249 is not output. A
      DTC C1249 is output. B

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts Click here.


    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    A

    INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) Click here

  9. CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. A01EXFAE13
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Turn the ignition switch off.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    3. Disconnect the skid control ECU connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A49-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
      A49-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V

      Tech Tips

      *: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts Click here.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here