TRANSMISSION CONTROL CABLE REMOVAL


  1. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    1. A01EWTR

      Lift the rear of the engine cover to detach the cover from the 2 pins, and then lift the front of the engine cover to detach the cover from the pin and remove the engine cover.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.

  2. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A01ETQR

      Remove the 9 clips and cool air intake duct seal.

  3. REMOVE INLET AIR CLEANER ASSEMBLY


    1. A01EV1L

      Remove the 2 bolts and inlet air cleaner assembly.

  4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A01EWQF

      Disconnect the vacuum switching valve assembly from the air cleaner hose.

    2. A01EXPW

      Disconnect the mass air flow meter connector and 2 wire harness clamps from the air cleaner cap sub-assembly.

    3. A01ETVQ

      Separate the fuel vapor feed hose from the air cleaner hose.

    4. A01EWXN

      Disconnect the ventilation hose from the cylinder head cover.

    5. A01EYB6

      Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.

    6. A01EWV3

      Release the 2 clamps and remove the air cleaner cap sub-assembly.

  5. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  6. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    1. A01EXKP

      Disconnect the wire harness clamp.

    2. Remove the 2 bolts and air cleaner case sub-assembly.

  7. REMOVE AIR BAG SENSOR ASSEMBLY

    Click here

  8. REMOVE ACCELERATOR PEDAL SENSOR ASSEMBLY (for LHD)

    Click here

  9. DISCONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD)


    1. Turn back the floor carpet.

    2. A01EVPG

      Remove the bolt and nut, and disconnect the No. 1 parking brake cable assembly.

  10. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY (for LHD)


    1. Move the shift lever to N.

    2. A01EUCX

      Disconnect the end of the transmission control cable assembly from the lower shift lever assembly.

    3. Disengage the 2 claws and disconnect the transmission control cable assembly from the lower shift lever assembly.

    4. A01ESVE

      Disconnect the wire harness clamp.

    5. A01EYG4

      Remove the nut and clip, and disconnect the transmission control cable assembly.

    6. A01EU3Y

      Turn back the dash panel insulator.

    7. Remove the 2 bolts and pull out the transmission control cable assembly from the body.

  11. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY (for RHD)


    1. Move the shift lever to N.

    2. A01EWN8

      Disconnect the end of the transmission control cable assembly from the lower shift lever assembly.

    3. Disengage the 2 claws and disconnect the transmission control cable assembly from the lower shift lever assembly.

    4. A01ESVE

      Disconnect the wire harness clamp.

    5. A01EYG4

      Remove the nut and clip, and disconnect the transmission control cable assembly.

    6. Turn back the floor carpet.

    7. A01EZ1OE01
      Text in Illustration
      *1 No. 1 parking brake cable assembly
      *2 Transmission control cable assembly

      Remove the bolt and disconnect the No. 1 parking brake cable assembly.

    8. Turn back the dash panel insulator.

    9. Remove the 2 bolts and pull out the transmission control cable assembly from the body.