SHIFT LEVER INSTALLATION


  1. INSTALL SHIFT LEVER SUPPORT


    1. A01ETNCE01

      Install the shift lever support with the 4 bolts in the sequence shown in the illustration.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  2. INSTALL LOWER SHIFT LEVER ASSEMBLY

    Note

    Check that the park/neutral position switch and the shift lever are in neutral.


    1. A01EU46E01

      Install the lower shift lever assembly with the 4 bolts in the sequence shown in the illustration.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. Connect the 3 clamps and 2 connectors.

    3. A01EVV8E03
      Text in Illustration
      *1 Slider
      *2 Lock Piece
      *a Slide
      *b Pull

      Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.

    4. A01EWE7E01
      Text in Illustration
      *1 Lock Piece

      Install the end of the transmission control cable to the lower shift lever assembly.

      Note


      • Check that the lock piece is pulled up.

      • Install the cable end all the way to the base of the pin.

    5. Push the lock piece into the adjuster case.

      Note


      • Check that the park/neutral position switch and the shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

  3. INSTALL NO. 1 CONSOLE BOX DUCT


    1. Install the No. 1 console box duct with the clip.

  4. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET


    1. Install the No. 1 console box mounting bracket to the lower shift lever assembly with the screw.

  5. INSTALL FLOOR CARPET BRACKET LH


    1. Engage the 2 guides.

    2. Install the floor carpet bracket LH with the 2 clips.

  6. INSTALL CONSOLE BOX INSERT


    1. A01EUCI

      Engage the clip and 4 guides as shown in the illustration.

    2. Install the console box insert with the 2 screws <C>.

    3. for RHD:


      1. Engage the 2 claws to connect the room temperature sensor.

  7. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    1. A01EVS5

      Engage the clip and 4 guides as shown in the illustration.

    2. Install the front No. 2 console box insert with the 2 screws <C>.

    3. for LHD:


      1. Engage the 2 claws to connect the room temperature sensor.

  8. INSTALL FRONT ASH RECEPTACLE ASSEMBLY


    1. Connect each connector.

    2. A01ETGW

      Engage the 2 clips.

    3. Install the front ash receptacle assembly with the 2 screws <C>.

  9. INSTALL FRONT CONSOLE UPPER PANEL GARNISH


    1. for Blank Type:


      1. A01EX5P

        Engage the 2 claws to install the front console upper panel garnish as shown in the illustration.

    2. for 3 Switch Hole Type:


      1. Connect each connector.

      2. A01EUCV

        Engage the 2 claws to install the front console upper panel garnish as shown in the illustration.

  10. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A01ET5P

      Engage the 2 clips and 4 guides.

    2. Install the 3 screws <C>.

    3. Close the lower instrument panel door.

    4. Install the lower instrument panel sub-assembly with the bolt <B> and screws <C>.

  11. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.

  12. INSTALL INSTRUMENT SIDE PANEL RH


    1. A01ETKO

      Engage the 3 guides as shown in the illustration.

    2. A01EXPG

      Engage the 4 claws to install the instrument side panel RH as shown in the illustration.

  13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01EXCIE01
      Text in Illustration
      *1 Alignment Mark (White)

      Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  14. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  15. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  16. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY


    1. w/o Driver Side Knee Airbag:


      1. Engage the 5 clips and 3 guides.

    2. w/ Driver Side Knee Airbag:


      1. Engage the 4 claws, 7 clips and 3 guides.

    3. Install the instrument panel sub-assembly with the 2 bolts <B>.

  17. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

  18. INSTALL INSTRUMENT SIDE PANEL LH


    1. Engage the 3 guides.

    2. A01ETDE

      Engage the 4 claws to install the instrument side panel LH as shown in the illustration.

  19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EWEQE01
      Text in Illustration
      *1 Alignment Mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. Engage the 2 clips.

    2. Install the cowl side trim sub-assembly LH with the clip.

  21. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Engage the 10 claws to install the front door scuff plate LH.

  22. INSTALL CONSOLE BOX ASSEMBLY

    Click here

  23. INSPECT SHIFT LEVER POSITION


    1. When the shift lever is moved from P to R with the engine switch on (IG) and brake pedal depressed, make sure that the shift lever moves smoothly and correctly the position.

    2. Start the engine and make sure that the vehicle moves forward when the shift lever is moved from N to D and moves rearward when the shift lever is moved to R.