TRANSMISSION CONTROL CABLE INSTALLATION


  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

    Note

    Before installing the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.


    1. Pass the transmission control cable assembly from the cabin to the engine compartment.

    2. Install the transmission control cable assembly with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    3. Install the dash panel insulator to the original position.

    4. Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

    5. Connect the transmission control cable assembly to the control shaft lever with the nut.

      Torque:
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }

      Note

      Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.

    6. Connect the wire harness clamp.

    7. Engage the 2 claws to connect the transmission control cable assembly.

    8. A01EVV8E03
      Text in Illustration
      *1 Slider
      *2 Lock Piece
      *a Slide
      *b Pull

      Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.

    9. A01EWE7E01
      Text in Illustration
      *1 Lock Piece

      Install the transmission control cable end to the lower shift lever assembly.

      Note


      • Check that the lock piece is pulled up.

      • Install the cable end all the way to the base of the pin.

    10. Push the lock piece into the adjuster case.

      Note


      • Check that the park/neutral position switch and the shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

  2. CONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY


    1. Install the No. 1 parking brake cable assembly with the bolt and nut.

      Torque:
      Bolt
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }
      Nut
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    2. Install the floor carpet to the original position.

  3. INSTALL ACCELERATOR PEDAL SENSOR ASSEMBLY

    Note


    • Avoid physical shock to the accelerator pedal sensor assembly.

    • Do not disassemble the accelerator pedal sensor assembly.

    • The accelerator pedal sensor assembly does not require lubrication.

    • Do not apply oil or other lubricants to the accelerator pedal sensor assembly. If applied, the accelerator pedal sensor assembly must be replaced.


    1. Temporarily install the accelerator pedal sensor assembly with the 2 bolts.

    2. A01EW4VE01

      Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    3. Connect the accelerator pedal sensor assembly connector.

  4. INSTALL AIRBAG SENSOR ASSEMBLY

    Click here

  5. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    1. Install the air cleaner case sub-assembly with the 3 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    2. Connect the wire harness clamp.

  6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. Install the air cleaner filter element to the air cleaner case sub-assembly.

    2. A01EWNAE01
      Text in Illustration
      *1 Air Cleaner Hose Clamp

      Connect the air cleaner cap sub-assembly to the throttle with motor body assembly and release the lock of the air cleaner hose clamp.

      Note


      • Align the groove of the air cleaner cap sub-assembly with the tab of the throttle with motor body assembly and install the hose.

      • Make sure that the tab of the air cleaner hose clamp stays within the range shown by *a.

    3. Connect the ventilation hose to the cylinder head cover.

    4. Install the air cleaner cap sub-assembly and tighten the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    5. Connect the wire harness clamp.

    6. Connect the mass air flow meter connector.

    7. Connect the purge line hose to the 2 clamps.

    8. Connect the 2 vacuum switching valve vacuum hoses.

    9. Connect the vacuum switching valve connector.

  7. INSTALL INLET AIR CLEANER ASSEMBLY


    1. Install the inlet air cleaner assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  8. INSTALL COOL AIR INTAKE DUCT SEAL


    1. Install the cool air intake duct seal with the 9 clips.

  9. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY


    1. Install the No. 1 engine cover sub-assembly with the 2 nuts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  10. INSPECT SHIFT LEVER POSITION


    1. When the shift lever is moved from P to R with the ignition switch ON and brake pedal depressed, make sure that the shift lever moves smoothly and correctly into the position.

    2. Start the engine and make sure that the vehicle moves forward when the shift lever is moved from N to D and moves rearward when the shift lever is moved to R.