STARTER (for 1.6 kW Type) REASSEMBLY


  1. INSTALL PLANETARY GEAR


    1. A01EWFWE06

      Apply high-temperature grease to the planetary gears and pin parts of the planetary shaft.

      Text in Illustration
      A01EUL1 High-temperature grease

    2. Install the 3 planetary gears.

  2. INSTALL RUBBER SEAL


    1. A01ETH8

      Install the rubber seal to the repair service starter kit.

  3. INSTALL STARTER ARMATURE ASSEMBLY


    1. A01ESVHE10

      Apply high-temperature grease to the washer and the armature shaft.

      Text in Illustration
      A01EUL1 High-temperature grease
    2. A01EUNIE04

      Apply high-temperature grease to the plate washer and bearing, as shown in the illustration.

      Text in Illustration
      A01EUL1 High-temperature grease
    3. A01EU5BE04
      Text in Illustration
      *1 Snap Ring Pliers

      Install the starter armature assembly to the starter commutator end frame assembly.

    4. Install the washer.

    5. Using snap ring pliers, securely install a new snap ring to the armature shaft groove.

      Note

      Be sure to install the snap ring, properly because it easily expands.

    6. A01EV94E03
      Text in Illustration
      *a Length

      Using a vernier caliper, measure the length of the snap ring.

      Maximum length
      5.0 mm (0.197 in.)

      If the length is more than the maximum, replace the snap ring with a new one.

  4. INSTALL STARTER COMMUTATOR END FRAME COVER


    1. A01EUU6

      Install the starter commutator end frame cover to the starter commutator end frame assembly.

  5. INSTALL STARTER ARMATURE PLATE


    1. A01ETC6E03
      Text in Illustration
      *a Keyway
      *b Key

      Insert the armature plate into the starter yoke assembly.

    2. Align the keyway of the starter armature plate with the key inside the starter yoke, and install the starter armature plate.

  6. INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY


    1. A01ESSXE03
      Text in Illustration
      *a Cutout
      *b Rubber

      Align the rubber of the end frame with the cutout of the starter yoke assembly.

    2. Install the starter commutator end frame assembly to the starter yoke assembly.

      Note

      The magnet of the starter yoke assembly may attract the starter armature when the starter commutator end assembly frame is installed, causing the magnet to break.

  7. INSTALL STARTER YOKE ASSEMBLY


    1. A01EWQ5E03
      Text in Illustration
      *a Protrusion
      *b Cutout

      Align the protrusion of the starter yoke assembly with the cutout of the repair service starter kit.

    2. A01EY76

      Install the starter yoke assembly with the 2 through-bolts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

  8. INSTALL MAGNET STARTER SWITCH ASSEMBLY


    1. A01ESOZE04

      Apply high-temperature grease to the plunger and the lever.

      Text in Illustration
      A01EUL1 High-temperature grease
    2. A01EV5S

      Pull the pinion gear and push down the lever.

    3. A01EX8XE03
      Text in Illustration
      *1 Plunger
      *2 Lever

      Temporarily install the magnet starter switch assembly by hooking the plunger into the upper side of the pinion drive lever.

    4. A01EWO6

      Install the magnet starter switch assembly with the 2 nuts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }
    5. A01EU4G

      Connect the lead wire to the magnet starter switch assembly with the nut.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }