OIL PUMP INSTALLATION


  1. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


    1. A01ETJC

      Apply a light coat of engine oil to 3 new gaskets.

    2. Install the 3 gaskets to the stiffening crankcase.

    3. A01EXUCE02
      Text in Illustration
      *1 Drive Rotor Spline
      *2 Crankshaft Timing Sprocket

      Align the drive rotor spline and the crankshaft timing sprocket as shown in the illustration.

    4. Apply seal packing in a line to the timing chain cover as shown in the following illustration.

      A01EVY3E01
      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.
      Apply Seal Packing as Follows
      Area Seal Packing Diameter (Round) Distance from Edge of Cover to Center of Seal Packing Seal Packing Application Length
      Seal Pacing Dimension (Flat)
      Dashed Line 3.0 mm (0.118 in.) 2.5 mm (0.0984 in.) -
      -
      A - A 3.0 mm (0.118 in.) 2.5 mm (0.0984 in.) -
      -
      B - B 5.0 mm (0.197 in.) 3.0 mm (0.118 in.) 28 mm (1.10 in.)
      7.0 mm (0.276 in.) or more wide and 3.0 mm (0.118 in.) or more thick
      C - C 7.0 mm (0.276 in.) 5.0 mm (0.197 in.) 25 mm (0.984 in.)
      13.0 mm (0.512 in.) or more wide and 3.0 mm (0.118 in.) or more thick
      D - D 5.0 mm (0.197 in.) 3.0 mm (0.118 in.) 26 mm (1.02 in.)
      7.0 mm (0.276 in.) or more wide and 3.0 mm (0.118 in.) or more thick
      E 3.0 mm (0.118 in.) 3.0 mm (0.118 in.) -
      -

      Note


      • When the contact surfaces are wet, clean the surfaces with non-residue solvent before applying seal packing.

      • Install the timing chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

      • After applying seal packing to the timing chain cover, install the engine mounting bracket within 10 minutes.

      • Do not apply oil for at least 4 hours after the installation.

      • Do not start the engine for at least 4 hours after the installation.

    5. A01EXO6E04
      Text in Illustration
      *a Bolt A
      *b Bolt B
      *c Bolt C
      *d Nut

      Temporarily install the timing chain cover with the 17 bolts and 2 nuts.

      Bolt Length
      Item Length Thread Diameter
      Bolt A 30 mm (1.18 in.) 8 mm (0.315 in.)
      Bolt B 35 mm (1.38 in.) 10 mm (0.394 in.)
      Bolt C 45 mm (1.77 in.) 8 mm (0.315 in.)

      Note

      Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.

    6. A01ET7ME01

      Tighten the 17 bolts and 2 nuts in several steps, in the sequence shown in the illustration.

      Torque:
      for bolt 1, 2, 3 and 4
      55 N*m  { 561 kgf*cm, 41 ft.*lbf }
      except bolt 1, 2, 3 and 4
      21 N*m  { 214 kgf*cm, 16 ft.*lbf }

  2. INSTALL ENGINE MOUNTING BRACKET RH


    1. A01EY7IE01

      Install the engine mounting bracket RH with the 5 bolts in the order shown in the illustration.

      Torque:
      for bolt 1, 2 and 3
      55 N*m  { 561 kgf*cm, 41 ft.*lbf }
      for bolt 4 and 5
      21 N*m  { 214 kgf*cm, 16 ft.*lbf }

      Note

      After applying seal packing to the timing chain cover, install the engine mounting bracket within 10 minutes.

  3. INSTALL TIMING CHAIN COVER OIL SEAL


    1. Apply MP grease to the lip of a new oil seal.

      Note


      • Do not allow foreign matter to contact the lip of the oil seal.

      • Do not allow MP grease to contact the dust seal.

    2. A01EU8NE01

      Using SST and a hammer, tap in the oil seal until its surface is flush with the timing chain cover edge.

      SST
      09223-22010

      Note


      • Keep the lip of the oil seal free from foreign matter.

      • Do not tap in the oil seal at an angle.

  4. INSTALL CRANKSHAFT PULLEY


    1. Align the pulley set key with the key groove of the crankshaft pulley.

    2. A01EV04E05
      Text in Illustration
      *a Hold
      *b Turn

      Using SST, hold the crankshaft pulley and install the pulley bolt.

      SST
      09213-54015
      09330-00021
      Torque:
      260 N*m  { 2651 kgf*cm, 192 ft.*lbf }

      Tech Tips

      SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)

  5. INSTALL CRANKSHAFT POSITION SENSOR


    1. Clean and degrease the threads of the bolt for the crankshaft position sensor.

    2. A01EXUJE07
      Text in Illustration
      *1 O-ring

      Apply a light coat of engine oil to the O-ring of the sensor.

    3. A01ET13E06
      Text in Illustration
      *1 Adhesive

      Apply adhesive to 2 or 3 threads of the bolt.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

    4. Install the sensor with the bolt.

      Torque:
      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

      Note

      Make sure that the O-ring is not cracked or does not jump out of position during installation.

    5. Connect the sensor connector.

  6. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    1. A01EWOV

      Install the V-ribbed belt tensioner with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  7. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    1. A01EV5L

      Apply a light coat of engine oil to 3 new gaskets.

    2. Install the 3 gaskets to the camshaft bearing caps.

    3. A01ET2UE05
      Text in Illustration
      *1 Upper Surface
      *2 Inner Lip
      *3 Outer Lip

      Visually check the spark plug tube gasket.

      OK
      Area Specified Condition
      Upper surface No scratches or deformation
      Outer lip No scratches or deformation
      Inner lip No scratches

      Tech Tips

      If the result is not as specified, replace the spark plug tube gasket.

    4. Install a new gasket to the cylinder head cover.

      Note

      Remove any oil from the contact surface.

    5. A01EU0SE03
      Text in Illustration
      *1 Seal packing
      *2 Timing Chain Cover
      *3 Camshaft Housing

      Apply seal packing as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Standard seal diameter
      3.0 to 6.0 mm (0.118 to 0.236 in.)
      Application width A
      5.0 mm (0.197 in.)

      Note


      • Remove any oil from the contact surface.

      • Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

    6. A01EUREE01

      Align the cylinder head cover with pin A. Then align the cylinder head cover with pin B and install the cylinder head cover.

    7. Install 3 new seal washers and the 16 bolts, and then tighten the bolts in the order shown in the illustration.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

      Note


      • Do not apply oil for at least 4 hours after the installation.

  8. INSTALL IGNITION COIL ASSEMBLY


    1. Install the 4 ignition coil assemblies with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Tech Tips

      Perform "Inspection After Repair" after replacing the ignition coil assembly Click here.

    2. Connect the 4 ignition coil assembly connectors.

  9. INSTALL ENGINE WIRE

  10. INSTALL ENGINE AND TRANSAXLE

    Click here