FUEL LID LOCK CONTROL CABLE ASSEMBLY (for RHD) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)

    Click here

  3. REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  6. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  8. REMOVE LAP BELT OUTER ANCHOR COVER

    Tech Tips

    Use the same procedure as for the LH side Click here.

  9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  10. REMOVE CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  11. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01EWHQ

      Disengage the 6 claws and remove the rear door scuff plate LH.

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  12. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. A01EXQTE01

      Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

      2. Repeat the step above for the other hook.

    2. w/ Seat Heater System:


      1. Disconnect the connector.

      2. A01EVEO

        Disengage the 2 clamps.

    3. Remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  13. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. A01EZ1N

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  14. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide LH.

    2. A01EY53

      Remove the bolt.

    3. Disengage the hook and remove the rear side seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  15. REMOVE LUGGAGE COMPARTMENT FLOOR MAT


    1. Remove the luggage compartment floor mat.

  16. REMOVE BAGGAGE HOLDER NET (w/ Partition Net)


    1. Remove the baggage holder net.

  17. REMOVE REAR FLOOR FINISH PLATE


    1. A01EY0R

      Remove the 5 clips.

    2. A01EYEN

      Disengage the 4 clips and remove the rear floor finish plate.

  18. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01EULLE01
      Text in Illustration
      *1 Pin

      Push the pin and remove the No. 1 luggage compartment trim hook.

  19. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. A01EU4O

      Remove the 3 clips.

    2. Disengage the fastener and remove the luggage compartment inner trim cover LH.

  20. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A01EYAQ

      Remove the screw.

    2. A01EXES

      Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. A01ETL7

      Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

  21. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY


    1. A01EU87

      Disengage the 2 clamps.

    2. A01EWEW

      Disengage the clamp and disconnect the wire harness.

    3. A01EV6W

      Disengage the 2 clamps and remove the 2 scuff plate clips.

    4. Turn back the floor carpet so that the fuel lid lock control cable sub-assembly can be removed.

    5. A01EVXXE01
      Text in Illustration
      *1 Tape
      *2 Fuel Lid Lock Control Cable Sub-assembly
      *3 Luggage Door Lock Control Cable Sub-assembly

      Remove the 2 pieces of tape that connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    6. A01EVPF

      Remove the No. 2 noise control plate.

    7. A01EW3VE01
      Text in Illustration
      *1 Cutout
      *2 Guide <A>

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.

    8. A01EU9GE01
      Text in Illustration
      *1 Cutout
      *2 Guide <B>

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.

    9. A01EUM8E01
      Text in Illustration
      *1 Cutout
      *2 Guide <C>
      *3 Guide <B>

      Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.

    10. A01EYRV

      Disengage the 2 claws and remove the fuel filler opening lid lock retainer.

    11. Disengage the 7 clamps and remove the fuel lid lock control cable sub-assembly.

      A01EYRDE01
      Text in Illustration
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Luggage Door Lock Control Cable Sub-assembly