FUEL LID LOCK CONTROL CABLE ASSEMBLY (for LHD) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)

    Click here

  3. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01EYU6

      Disengage the 10 claws and remove the front door scuff plate LH.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the front door opening trim weatherstrip.

  6. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01EWHQ

      Disengage the 6 claws and remove the rear door scuff plate LH.

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  7. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the rear door opening trim weatherstrip LH.

  8. REMOVE LAP BELT OUTER ANCHOR COVER


    1. A01EWZL

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01EXLX

      Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

  10. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. A01ETYO

      Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

  11. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)


    1. A01EYIPE01

      Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

      2. Repeat the step above for the other hook.

    2. Remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  12. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)


    1. A01EZ1N

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the LH side and RH side.

  13. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.

    2. A01EY53

      Remove the bolt.

    3. Disengage the hook and remove the rear side seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  14. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)


    1. A01EWH4E01

      Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

      2. Repeat the step above for the other hook.

    2. w/ Seat Heater System:


      1. Disconnect the 2 seat heater connectors.

    3. Remove the rear seat cushion assembly.

  15. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    1. A01EZ1N

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  16. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

  17. REMOVE REAR SEATBACK COVER (for Reclining Seat Type)


    1. A01EUWN

      Disengage the 4 claws and remove the 2 rear seatback covers.

      Tech Tips

      Use the same procedure as for the LH side.

  18. REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)


    1. w/ Rear Seat Side Airbag:


      1. Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.

    2. Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.

    3. A01EVHV

      Disengage the 2 hooks and disconnect the cover.

    4. Remove the 2 nuts, 2 bolts and rear seatback assembly LH.

  19. REMOVE REAR SEAT SIDE GARNISH LH (for Reclining Seat Type)


    1. A01EY25

      Remove the bolt.

    2. Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.

  20. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    1. A01ETWR

      Remove the 13 clips and luggage compartment door cover.

  21. REMOVE LUGGAGE COMPARTMENT FLOOR MAT


    1. Remove the luggage compartment floor mat.

  22. REMOVE BAGGAGE HOLDER NET (w/ Partition Net)


    1. Remove the baggage holder net.

  23. REMOVE REAR FLOOR FINISH PLATE


    1. A01EY0R

      Remove the 5 clips.

    2. A01EYEN

      Disengage the 4 clips and remove the rear floor finish plate.

  24. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01EULLE01
      Text in Illustration
      *1 Pin

      Push the pin and remove the No. 1 luggage compartment trim hook.

  25. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. A01EU4O

      Remove the 3 clips.

    2. Disengage the fastener and remove the luggage compartment inner trim cover LH.

  26. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A01EXDI

      Remove the screw.

    2. A01EYDG

      Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. A01EVE2

      Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

  27. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY


    1. A01EUFL

      Disengage the 2 clamps.

    2. A01EU8W

      Disengage the clamp and disconnect the wire harness.

    3. A01ETLE

      Disengage the 2 clamps and remove the 2 scuff plate clips.

    4. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.

    5. A01EYD8

      Disengage the guide as shown in the illustration.

    6. A01EXBV

      Disconnect the luggage door lock control cable sub-assembly.

    7. A01EV9H

      Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.

    8. A01EW3VE01
      Text in Illustration
      *1 Cutout
      *2 Guide <A>

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.

    9. A01EU9GE01
      Text in Illustration
      *1 Cutout
      *2 Guide <B>

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.

    10. A01EUM8E01
      Text in Illustration
      *1 Cutout
      *2 Guide <C>
      *3 Guide <B>

      Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.

    11. A01EYRV

      Disengage the 2 claws and remove the fuel filler opening lid lock retainer.

    12. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

      A01EW1VE01
      Text in Illustration
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Luggage Door Lock Control Cable Sub-assembly
    13. Using a knife, cut off the clamp as shown in the illustration.

      A01EUCRE01
      Text in Illustration
      *1 Tape - -
      *a Cut - -

      Note

      Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    14. Remove the clamp.

    15. Remove the 3 pieces of tape and fuel lid lock control cable sub-assembly.