LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for LHD) INSTALLATION


  1. INSTALL LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    1. Install the luggage door lock control cable sub-assembly to the fuel lid lock control cable sub-assembly with the clamp and the 3 pieces of tape as shown in the illustration.

      A01EX11E01
      Text in Illustration
      *1 Clamp (A) *2 Clamp
      *3 Luggage Door Lock Control Cable Sub-assembly *4 Fuel Lid Lock Control Cable Sub-assembly
      *5 Tape - -
      Standard Clearance
      Area Measurement Area Measurement
      a 295 to 305 mm (11.6 to 12.0 in.) b 880 to 900 mm (2.29 to 2.95 ft.)
      c 2090 to 2110 mm (6.86 to 6.92 ft.) d 2970 to 2990 mm (8.86 to 9.81 ft.)
      e 5.0 mm (0.197 in.) or less - -

      Note


      • Wrap tape around the designated position 1 to 3 times.

      • Make sure that the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly are not kinked.

    2. Engage the 10 clamps and install the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    3. A01EUSDE01
      Text in Illustration
      *1 Cutout
      *2 Guide

      Align the cutouts and guides, and then insert the fuel filler opening lid lock retainer.

    4. A01EW40E01
      Text in Illustration
      *1 Claw

      Engage the 2 claws and install the fuel filler opening lid lock retainer.

    5. A01ETQC

      Engage the 2 claws and install the fuel lid lock control cable sub-assembly.

    6. Engage the clamp and connect the luggage door lock control cable sub-assembly.

    7. Connect the luggage door lock control cable sub-assembly.

    8. A01ESV5

      Engage the guide as shown in the illustration.

    9. Return the floor carpet to the original position.

    10. Engage the 2 clamps and install the 2 scuff plate clips.

    11. Engage the 3 clamps to connect the wire harness.

  2. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A01EVE2E01
      Text in Illustration
      *1 Luggage Door Lock Control Cable Sub-assembly
      *2 Fuel Lid Lock Control Cable Sub-assembly

      Connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly to the fuel lid lock open lever sub-assembly.

    2. A01EWD8

      Engage the guide and install the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. Install the screw.

  3. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. Install the 3 clips.

    2. Engage the fastener and install the luggage compartment inner trim cover LH.

  4. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01EU3EE01
      Text in Illustration
      *1 Pin

      Engage the pin to install the No. 1 luggage compartment trim hook.

  5. INSTALL REAR FLOOR FINISH PLATE


    1. A01EWNX

      Engage the 4 clips and install the rear floor finish plate.

    2. Install the 5 clips.

  6. INSTALL BAGGAGE HOLDER NET (w/ Partition Net)


    1. Install the baggage holder net.

  7. INSTALL LUGGAGE COMPARTMENT FLOOR MAT


    1. Install the luggage compartment floor mat.

  8. INSTALL LUGGAGE COMPARTMENT DOOR COVER


    1. A01ETWR

      Install the luggage compartment door cover with the 13 clips.

  9. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    1. Place the rear side seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Engage the hook to install the rear side seatback assembly LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the rear seat outer belt to the rear seat shoulder belt guide LH.

  10. INSTALL REAR SEAT SIDE GARNISH LH (for Reclining Seat Type)


    1. Engage the guide, claw and 2 clips.

    2. Install the rear seat side garnish LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  11. INSTALL CENTER PILLAR LOWER GARNISH LH


    1. Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.

  12. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. Install the floor anchor of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the front seat outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  13. INSTALL LAP BELT OUTER ANCHOR COVER


    1. Engage the 3 claws to install the lap belt outer anchor cover.

  14. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EY2WE01
      Text in Illustration
      *1 Alignment Mark (Red)

      Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  15. INSTALL REAR DOOR SCUFF PLATE LH


    1. Engage the 6 claws to install the rear door scuff plate LH.

      Tech Tips

      Engage the claws from the rear side of the scuff plate.

  16. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EWEQE01
      Text in Illustration
      *1 Alignment Mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  17. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Engage the 10 claws to install the front door scuff plate LH.

  18. INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)


    1. A01EVL5

      Engage the claw to install a new rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  19. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A01ETRH

      Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

    3. Confirm that the rear seat cushion assembly is firmly installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.

  20. INSTALL REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)


    1. Place the rear seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH with the 2 bolts and 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Engage the 2 hooks to install the cover.

    4. Connect the 2 rear seat belts to the 2 rear seat shoulder belt guides.

    5. w/ Rear Seat Side Airbag:


      1. Connect each connector and clamp to the child restraint anchor bracket sub-assembly LH.

  21. INSTALL REAR SEATBACK COVER (for Reclining Seat Type)


    1. Engage the 4 claws to install the 2 rear seatback covers.

      Tech Tips

      Use the same procedure as for the LH side.

  22. INSTALL REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

  23. INSTALL REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    1. A01EVL5

      Engage the claw to install a new rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  24. INSTALL REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. w/ Seat Heater System:


      1. Connect the 2 seat heater connectors.

    3. A01EX1E

      Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

    4. Confirm that the rear seat cushion assembly is firmly installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the seat cushion assembly.

  25. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)

    Click here

  26. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

    Click here