BACK WINDOW GLASS REMOVAL


  1. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  2. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    1. A01EYH8

      Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.

  3. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    1. A01EXY3

      Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.

  4. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    1. A01EW7GE01
      Text in Illustration
      *A for Fold Down Seat Type
      *B

      for Reclining Seat Type

      w/o Seat Heater System
      *C

      for Reclining Seat Type

      w/ Seat Heater System

      Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.

  5. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    1. A01EW3F

      Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.

  6. REMOVE CENTER STOP LIGHT SET (w/o Rear Sunshade)


    1. A01EXDXE01

      Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.

    2. A01ET7Q

      Turn the center stop light set 180 degrees as shown by the arrow in the illustration.

      Tech Tips

      This makes it easier to disconnect the connector.

    3. Disconnect the connector and remove the center stop light set.

  7. REMOVE REAR SEAT SHOULDER BELT COVER


    1. A01ET04

      Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.

      Tech Tips

      Use the same procedure for the other 2 rear seat shoulder belt covers.

  8. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)


    1. A01EXA0E01
      Text in Illustration
      *1 Protective Tape

      Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.

      Tech Tips

      Tape the tips of pliers before use.

    2. Disengage the 5 guides.

    3. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.

  9. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)


    1. A01EWD9E01
      Text in Illustration
      *1 Protective Tape

      Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.

      Tech Tips

      Tape the tips of pliers before use.

    2. Disengage the guide.

    3. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.

  10. REMOVE BACK WINDOW GLASS SUB-ASSEMBLY


    1. Disconnect each connector.

    2. A01EXKUE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area around the installation position of the back window glass on the vehicle body to prevent it from being scratched.

      Tech Tips

      Apply protective tape to the vehicle body to prevent it from being scratched.

    3. A01EYE8E01
      Text in Illustration
      *1 Stopper
      *2 Piano Wire

      Pass a piano wire between the vehicle body and glass from the interior.

    4. Tie both wire ends to wooden blocks or similar objects.

    5. Cut off the adhesive by pulling the piano wire around the back window glass.

      Note

      When separating the back window glass, take care not to damage the paint or interior and exterior ornaments.

    6. A01EUZXE01
      Text in Illustration
      *1 Matchmark

      Place matchmarks on the back window glass and vehicle body on the locations indicated in the illustration.

      Tech Tips

      Matchmarks are not needed to be placed if the back window glass will not be reused.

    7. Disconnect the back window glass stoppers.

      A01EYO8E01
      Text in Illustration
      *A 1-piece type *B 2-piece type
      *1 No. 1 Back Window Glass Stopper *2 No. 2 Back Window Glass Stopper

      Note


      • There are No. 1 and No. 2 stoppers on the back window glass as shown in the illustration. Be careful not to damage the back window glass when cutting off the adhesive.

      • To prevent the back window glass from falling when performing this operation, be sure to hold the back window glass using suction cups.

      Tech Tips

      Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.

    8. Using suction cups, remove the back window glass sub-assembly.

      Note


      • Be careful not to drop the back window glass.

      • Leave as much adhesive on the vehicle body as possible when removing the back window glass.

  11. REMOVE BACK WINDOW GLASS ADHESIVE DAM


    1. When reusing the back window glass:


      1. A01EXFBE01
        Text in Illustration
        *1 Back Side

        Using a scraper, remove the back window glass adhesive dam.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the back window glass adhesive dam with a new one.

  12. REMOVE BACK WINDOW OUTSIDE MOULDING


    1. When reusing the back window glass:


      1. A01EYBTE01
        Text in Illustration
        *1 Back Side

        Using a scraper, remove the back window outside moulding.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the back window outside moulding with a new one.

  13. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 1-piece Type)


    1. When reusing the back window glass:


      1. A01ESPBE01
        Text in Illustration
        *1 Back Side

        Using a scraper, remove the 2 No. 1 back window glass stoppers.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the No. 1 back window glass stoppers with new ones.

  14. REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)


    1. When reusing the back window glass:


      1. A01ESPBE01
        Text in Illustration
        *1 Back Side

        Using a scraper, remove the 2 No. 2 back window glass stoppers.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the No. 2 back window glass stoppers with new ones.

  15. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)


    1. A01EX8O

      Remove the 2 No. 1 back window glass stoppers.

      Note

      Be sure to replace the No. 1 back window glass stoppers with new ones.

  16. CLEAN BACK WINDOW GLASS


    1. Using a scraper, remove any adhesive dam and adhesive residue from the back window glass.

      Note

      Be careful not to damage the back window glass.

    2. A01EYDB

      Clean the outer circumference of the back window glass with a non-residue solvent.

      Note


      • Do not touch the glass surface after cleaning it.

      • Be careful not to damage the glass.

      • Even if using new glass, clean it with a non-residue solvent.

  17. CLEAN VEHICLE BODY


    1. A01EWFKE07
      Text in Illustration
      *1 Adhesive
      *2 Body

      Clean and shape the contact surface of the vehicle body.


      1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

        Note

        Be careful not to damage the vehicle body.

        Tech Tips

        Leave as much adhesive on the vehicle body as possible.

      2. Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.

        Tech Tips

        Even if all the adhesive has been removed, clean the vehicle body.