POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.


  1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

    Note

    The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.


    1. A01EYPV

      Using a T25 "TORX" socket wrench, install the rear power window regulator motor assembly with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      When replacing the rear window regulator, a new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

  2. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

    2. Install the temporary bolt to the rear door window regulator assembly.

    3. A01EV9QE02
      Text in Illustration
      *1 Temporary Bolt

      Temporarily install the rear door window regulator assembly.

    4. Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A01ETPG

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  4. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

    2. A01EWEY

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  5. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. A01EVGG

      Install the rear door lower window frame sub-assembly with the screw and 2 bolts.

  6. INSTALL REAR DOOR GLASS RUN


    1. A01ETSR

      Install the rear door glass run.

  7. INSTALL REAR DOOR WEATHERSTRIP


    1. A01EXAC

      Install the upper part of rear door weatherstrip as shown in the illustration.

  8. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the rear door panel.

    2. A01EXSNE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the connector.

  9. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A01EW36

      Install the rear door inner glass weatherstrip.

  10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01EWKA

      Install the No. 1 door scuff plate clamp as shown in the illustration.

    2. A01EY4QE01
      Text in Illustration
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    3. Connect the connector.

    4. A01EYELE01
      Text in Illustration
      *1 Reference Boss

      Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.

    5. A01EXGD

      Engage the 8 clips and install the rear door trim board sub-assembly.

    6. Install the 3 screws.

    7. If protective tape has been applied, remove it.

  11. INSTALL REAR ARMREST ASSEMBLY


    1. A01EYTY

      Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.

  12. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A01EWWS

      Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

  13. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01ET39

      Engage the 3 claws to install the rear door inside handle bezel plug.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Click here

  15. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  16. INSPECT POWER WINDOW OPERATION

    Click here