ROOF HEADLINING REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01EYU6

      Disengage the 10 claws and remove the front door scuff plate LH.

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01EVAC

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  5. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the front door opening trim weatherstrip LH.

  6. REMOVE FRONT PILLAR GARNISH LH


    1. A01EYF5E01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. A01EXVEE01

      While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.

    3. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

    4. A01EY91E01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  7. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  10. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  11. REMOVE REAR SEAT HEADREST ASSEMBLY

  12. REMOVE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    1. Disconnect the rear seat outer belt assembly from the rear seat center shoulder belt guide.

    2. Fold down the rear seatback assembly LH.

    3. A01EW9GE01
      Text in Illustration
      *1 Fastener

      Disengage the fastener as shown in the illustration.

    4. w/o Seat Heater System:


      1. A01EWPN

        Remove the 2 bolts and rear seatback assembly LH.

        Note

        Be careful not to damage the vehicle body.

    5. w/ Seat Heater System:


      1. A01EWPN

        Remove the 2 bolts and disconnect the rear seatback assembly LH.

      2. A01EVU6

        Disconnect the connector.

      3. Disengage the clamp and remove the rear seatback assembly LH.

        Note

        Be careful not to damage the vehicle body.

  13. REMOVE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)


    1. Fold down the rear seatback assembly RH.

    2. A01EYWVE01
      Text in Illustration
      *1 Fastener

      Disengage the fastener as shown in the illustration.

    3. w/o Seat Heater System:


      1. A01EV2K

        Remove the 2 bolts and rear seatback assembly RH.

        Note

        Be careful not to damage the vehicle body.

    4. w/ Seat Heater System:


      1. A01EV2K

        Remove the 2 bolts and disconnect the rear seatback assembly RH.

      2. A01EYEC

        Disconnect the connector.

      3. Disengage the clamp and remove the rear seatback assembly RH.

        Note

        Be careful not to damage the vehicle body.

  14. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)


    1. A01EXQTE01

      Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

      2. Repeat the step above for the other hook.

    2. w/ Seat Heater System:


      1. Disconnect the connector.

      2. A01EVEO

        Disengage the 2 clamps.

    3. Remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  15. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)


    1. A01EZ1N

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  16. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide LH.

    2. A01EY53

      Remove the bolt.

    3. Disengage the hook and remove the rear side seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  17. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)


    1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide RH.

    2. A01EXK1

      Remove the bolt.

    3. Disengage the hook and remove the rear side seatback assembly RH.

      Note

      Be careful not to damage the vehicle body.

  18. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

  19. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)


    1. A01EWH4E01

      Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

      2. Repeat the step above for the other hook.

    2. Disconnect the 2 seat heater connectors.

    3. Remove the rear seat cushion assembly.

  20. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    1. A01EZ1N

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  21. REMOVE REAR SEATBACK COVER (for Reclining Seat Type)


    1. A01EUWN

      Disengage the 4 claws and remove the 2 rear seatback covers.

      Tech Tips

      Use the same procedure as for the LH side.

  22. REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)


    1. w/ Rear Seat Side Airbag:


      1. Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.

    2. Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.

    3. A01EVHV

      Disengage the 2 hooks and disconnect the cover.

    4. Remove the 2 nuts, 2 bolts and rear seatback assembly LH.

  23. REMOVE REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type)


    1. w/ Rear Seat Side Airbag:


      1. Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly RH.

    2. Disengage the rear seat belt from the rear seat shoulder belt guide.

    3. A01EUMS

      Disengage the 2 hooks and disconnect the cover.

    4. Remove the 2 nuts, 2 bolts and rear seatback assembly RH.

  24. REMOVE CENTER SEATBACK ASSEMBLY (for Reclining Seat Type)


    1. Disconnect the connector.

    2. A01EUY4

      Remove the 2 bolts.

    3. Disengage the hook and remove the center seatback assembly as shown in the illustration.

  25. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01EWHQ

      Disengage the 6 claws and remove the rear door scuff plate LH.

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  26. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the rear door opening trim weatherstrip LH.

  27. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    1. A01EWZL

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  28. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01EXLX

      Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

  29. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. A01ETYO

      Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

  30. REMOVE CENTER PILLAR UPPER GARNISH LH


    1. A01EZ41

      Remove the 2 screws.

    2. Disengage the clip.

    3. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.

  31. REMOVE REAR SEAT SIDE GARNISH LH (for Reclining Seat Type)


    1. A01EY25

      Remove the bolt.

    2. Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.

  32. REMOVE ROOF SIDE INNER GARNISH LH


    1. A01EXPK

      Disengage the 5 clips.

    2. Disengage the guide and remove the roof side inner garnish LH.

  33. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  34. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side.

  35. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  36. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  37. REMOVE CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  38. REMOVE CENTER PILLAR UPPER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  39. REMOVE REAR SEAT SIDE GARNISH RH (for Reclining Seat Type)

    Tech Tips

    Use the same procedure as for the LH side.

  40. REMOVE ROOF SIDE INNER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  41. REMOVE FRONT SEAT ASSEMBLY LH

    for Manual Seat Click here

    for Power Seat Click here

  42. REMOVE FRONT SEAT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  43. REMOVE INSTRUMENT PANEL SAFETY PAD

    Click here

  44. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. except TMMR Made:


      1. A01EWTN

        Disengage the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow shown in the illustration.

      2. A01ETTD

        Disengage the 6 claws and remove the inner rear view mirror stay holder cover.

    2. for TMMR Made:


      1. A01EVTQ

        Disengage the 2 guides and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow shown in the illustration.

    3. A01ETVM

      Disengage the 2 claws and remove the inner rear view mirror stay holder cover.

  45. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A01EUNY

      Disengage the 2 claws and remove the rain sensor cover as shown in the illustration.

  46. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)


    1. A01ETHN

      Using a moulding remover, disengage the 4 clips.

    2. Disconnect the connector and remove the roof console box assembly.

  47. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)


    1. A01EWDV

      Using a moulding remover, disengage the 4 clips.

    2. Disconnect the connector and remove the roof console box assembly.

  48. REMOVE SPOT LIGHT ASSEMBLY


    1. A01EUCKE01
      Text in Illustration
      *a Front

      Using a moulding remover, disengage the 4 claws.

    2. Disconnect the connector and remove the spot light assembly.

  49. REMOVE ASSIST GRIP SUB-ASSEMBLY


    1. A01EYSAE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01ETV3

      Disengage the 2 clips and remove the assist grip sub-assembly.

    3. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the RH side.

  50. REMOVE REAR ASSIST GRIP ASSEMBLY LH


    1. A01ETUEE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01EY84

      Disengage the 2 clips and remove the rear assist grip assembly LH.

    3. Remove the 2 clips from the vehicle body.

  51. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  52. REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    1. Remove the sliding roof opening trim moulding.

  53. REMOVE VISOR BRACKET COVER (for LH Side)


    1. A01ETL9

      Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.

  54. REMOVE VISOR ASSEMBLY LH


    1. A01EVYN

      Remove the 2 screws and visor assembly LH.

  55. REMOVE VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  56. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  57. REMOVE VISOR HOLDER


    1. A01EZ0DE01

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

      Tech Tips

      Use the same procedure for the other visor holder.

  58. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    1. w/ EC Mirror:


      1. Disconnect the connector.

    2. w/ Rain Sensor:


      1. Disconnect the connector.

    3. w/ Television Antenna:


      1. Disconnect the connector.

    4. Remove the bolt and disconnect the bracket from the front pillar RH.

      A01EVI6
    5. Disengage the 3 clamps from the front pillar RH.

    6. Disengage the 4 clamps from the front pillar LH.

    7. Disengage the 2 clamps and disconnect the connector from the rear pillar RH.

    8. Remove the 2 clips.

    9. Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

      Tech Tips

      Leave the 2 clips in the vehicle.

    10. A01EYVS

      Remove the roof headlining assembly from the vehicle through the front passenger side door.

      Note

      Do not damage the roof headlining assembly or body interior.

    11. A01EWFX

      Remove the 2 clips from the vehicle body as shown in the illustration.

  59. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    1. w/ EC Mirror:


      1. Disconnect the connector.

    2. w/ Rain Sensor:


      1. Disconnect the connector.

    3. w/ Television Antenna:


      1. Disconnect the connector.

    4. Disconnect the connector from the sliding roof drive gear assembly.

      A01EYFD
    5. Remove the bolt and disconnect the bracket from the front pillar RH.

    6. Disengage the 3 clamps from the front pillar RH.

    7. Disengage the 4 clamps from the front pillar LH.

    8. Disengage the 2 clamps and disconnect the connector from the rear pillar RH.

    9. Remove the 2 clips.

    10. Disengage the 2 fasteners.

    11. Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

      Tech Tips

      Leave the 2 clips in the vehicle.

    12. A01EUBJ

      Remove the roof headlining assembly from the vehicle through the front passenger side door.

      Note

      Do not damage the roof headlining assembly or body interior.

    13. A01EWFX

      Remove the 2 clips from the vehicle body as shown in the illustration.