REAR POWER OUTLET SOCKET REMOVAL


  1. PRECAUTION (w/ Rear Seat Side Airbag)

    CAUTION:


    • Be sure to read Precaution thoroughly before servicing Click here.

    • If the side airbag has deployed, replace the rear seat airbag assembly, rear seatback frame subassembly, separate type rear seatback cover and separate type rear seatback pad with a new one.

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR SEAT HEADREST ASSEMBLY

  4. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY

  5. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. A01EWH4E01

      Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

      2. Repeat the step above for the other hook.

    2. w/ Seat Heater System:


      1. Disconnect the 2 seat heater connectors.

    3. Remove the rear seat cushion assembly.

  6. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. A01EZ1N

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  7. REMOVE REAR SEATBACK COVER


    1. A01EUWN

      Disengage the 4 claws and remove the 2 rear seatback covers.

      Tech Tips

      Use the same procedure as for the LH side.

  8. REMOVE REAR SEATBACK ASSEMBLY LH


    1. w/ Rear Seat Side Airbag:


      1. Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.

    2. Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.

    3. A01EVHV

      Disengage the 2 hooks and disconnect the cover.

    4. Remove the 2 nuts, 2 bolts and rear seatback assembly LH.

  9. REMOVE REAR SEATBACK ASSEMBLY RH


    1. w/ Rear Seat Side Airbag:


      1. Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly RH.

    2. Disengage the rear seat belt from the rear seat shoulder belt guide.

    3. A01EUMS

      Disengage the 2 hooks and disconnect the cover.

    4. Remove the 2 nuts, 2 bolts and rear seatback assembly RH.

  10. REMOVE CENTER SEATBACK ASSEMBLY


    1. Disconnect the connector.

    2. A01EUY4

      Remove the 2 bolts.

    3. Disengage the hook and remove the center seatback assembly as shown in the illustration.

  11. REMOVE CENTER SEAT ARMREST INNER PLATE


    1. A01EX0A

      Disengage the 6 claws and separate the 4 guides, and remove the center seat armrest inner plate.

  12. REMOVE REAR CENTER SEATBACK FRAME WITH COVER AND PAD


    1. A01EU9R

      Remove the 2 nuts.

    2. Disengage the 2 claws and remove the rear center seatback frame with cover and pad.

  13. REMOVE CENTER SEAT ARMREST BRACKET SUB-ASSEMBLY


    1. A01EYP1

      Disengage the 3 clamps.

    2. Remove the 2 bolts, 2 washers and center seat armrest bracket sub-assembly.

  14. REMOVE REAR SEAT CENTER ARMREST BOX ASSEMBLY


    1. A01ESTS

      Disengage the 4 hooks and remove the rear seat center armrest box assembly from the rear seat center armrest.

  15. REMOVE COOLER CONTROL SWITCH ASSEMBLY


    1. A01ETO7

      Remove the 2 screws.

    2. Separate the guide and remove the rear seat center armrest door sub-assembly.

    3. A01EY24

      Remove the screw.

    4. Using a moulding remover, disengage the 8 claws and 3 guides, and remove the rear seat armrest plate.

    5. A01EX0K

      Disengage the 4 claws.

    6. A01EYD7

      Disconnect each connector to remove the cooler control switch assembly.

  16. REMOVE REAR NO. 1 POWER OUTLET SOCKET ASSEMBLY


    1. A01EUHK

      Disengage the guide.

    2. A01EVMO

      Disengage the 3 clamps and turn back the rear seat center armrest cover as shown in the illustration.

    3. A01ETI8

      Disconnect the connector.

    4. A01EUSME01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the claw and remove the rear No. 1 power outlet socket assembly as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

  17. REMOVE REAR POWER OUTLET SOCKET COVER


    1. A01EVB7

      Disengage the 2 claws and remove the rear power outlet socket cover as shown in the illustration.