REAR SEAT RECLINING CONTROL CABLE INSTALLATION


  1. INSTALL REAR SEATBACK LOCK ASSEMBLY LH (REAR SEAT LOCK CONTROL CABLE LH)


    1. Install the rear seatback lock assembly LH (rear seat lock control cable LH) with the 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    2. A01EXCX

      Engage the hook in the order indicated in the illustration.

  2. INSTALL REAR SEATBACK LOCK ASSEMBLY RH (REAR SEAT LOCK CONTROL CABLE RH)

    Tech Tips

    Use the same procedure as for the LH side.

  3. INSTALL ROOM PARTITION BOARD RH


    1. Engage the 5 clips to install the room partition board RH.

    2. Install the 2 clips.

  4. INSTALL ROOM PARTITION BOARD LH


    1. Engage the 4 clips, 2 claws and guide to install the room partition board LH.

  5. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)


    1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    2. A01EVT8

      Engage the 5 guides and 3 clips to install the package tray trim panel assembly.

  6. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)


    1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    2. A01ESS4

      Engage the guide and 3 clips to install the package tray trim panel assembly.

  7. INSTALL REAR SEAT SHOULDER BELT COVER


    1. A01ETO9

      Engage the 4 guides and 2 claws to install the rear seat shoulder belt cover.

      Tech Tips

      Use the same procedure for the other 2 rear seat shoulder belt covers.

  8. INSTALL CENTER STOP LIGHT SET (w/o Rear Sunshade)


    1. Connect the connector.

    2. Temporarily install the center stop light set.

    3. A01EUO9E01

      Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to engage the 4 claws.

  9. INSTALL ROOF SIDE INNER GARNISH LH


    1. Engage the guide.

    2. Engage the 5 clips to install the roof side inner garnish LH.

  10. INSTALL ROOF SIDE INNER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  11. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    1. A01EWZBE01
      Text in Illustration
      *1 Protruding Part

      Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note


      • Install the rear seat inner with center belt assembly LH with the arrow on the anchor part facing the front of the vehicle.

      • Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.

  12. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    1. Install the child restraint seat anchor bracket sub-assembly LH with the 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  13. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    1. A01EZ38E05
      Text in Illustration
      *a Protruding Part

      Connect the floor anchor of the rear seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.

  14. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    1. A01EVCEE02
      Text in Illustration
      *a Protruding Part

      Connect the floor anchor of the rear seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.

  15. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01EY2WE01
      Text in Illustration
      *1 Alignment Mark (Red)

      Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  16. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01EXYTE01
      Text in Illustration
      *1 Alignment Mark (Blue)

      Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  17. INSTALL REAR SIDE SEATBACK ASSEMBLY LH


    1. Place the rear side seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Engage the hook to install the rear side seatback assembly LH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide LH.

  18. INSTALL REAR SIDE SEATBACK ASSEMBLY RH


    1. Place the rear side seatback assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Engage the hook to install the rear side seatback assembly RH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide RH.

  19. INSTALL REAR SEAT CUSHION LOCK HOOK


    1. A01EVL5

      Engage the claw to install a new rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  20. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. w/ Seat Heater System:


      1. Engage the 2 clamps.

      2. Connect the connector.

    3. A01EUI2

      Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

    4. Confirm that the rear seat cushion assembly is firmly installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.

  21. INSTALL REAR SEATBACK ASSEMBLY LH


    1. Place the rear seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. w/ Seat Heater System:


      1. Engage the clamp.

      2. Connect the connector.

    3. Install the rear seatback assembly LH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    4. A01ET30

      Engage the fastener as shown in the illustration.

    5. Raise the rear seatback assembly LH.

    6. Connect the rear seat outer belt assembly to the rear seat center shoulder belt guide.

  22. INSTALL REAR SEATBACK ASSEMBLY RH


    1. Place the rear seatback assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. w/ Seat Heater System:


      1. Engage the clamp.

      2. Connect the connector.

    3. Install the rear seatback assembly RH with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    4. A01EYBB

      Engage the fastener as shown in the illustration.

    5. Raise the rear seatback assembly RH.

  23. INSTALL REAR SEAT HEADREST ASSEMBLY