REAR SEATBACK HEATER (for Reclining Seat Type) INSTALLATION


  1. INSTALL SEPARATE TYPE REAR SEATBACK COVER (REAR SEATBACK HEATER SUB-ASSEMBLY)


    1. A01ET4N

      Using hog ring pliers, install the separate type rear seatback cover (rear seatback heater sub-assembly) to the separate type rear seatback pad with 10 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  2. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD


    1. Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.

    2. w/ Seat Heater System:


      1. Engage the clamp to connect the seat heater wire harness to the rear seatback frame sub-assembly LH.

    3. A01EXRE

      Engage the 4 claws to install the 2 rear seat headrest supports.

    4. w/ Rear Seat Side Airbag:


      1. A01EW7T

        Install the airbag bracket with the nut.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

        CAUTION:


        • For vehicles with side airbags, the seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.

        • Make sure that the strap is not twisted after installing the bracket.

        • Install the bracket securely.

    5. A01EXIY

      Using hog ring pliers, install 12 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    6. Engage each hook to install the separate type rear seatback cover with pad.

  3. INSTALL REAR SEAT SHOULDER BELT GUIDE


    1. A01EUZN

      Engage the guide.

    2. Install the rear seat shoulder belt guide LH with the 2 screws.

  4. INSTALL REAR SEAT CENTER SHOULDER BELT GUIDE (for LH Side)


    1. A01EW35

      Engage the guide.

    2. Install the rear seat center shoulder belt guide with the 2 screws.

  5. INSTALL REAR SEATBACK ASSEMBLY


    1. Place the rear seatback assembly LH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH with the 2 bolts and 2 nuts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Engage the 2 hooks to install the cover.

    4. Connect the 2 rear seat belts to the 2 rear seat shoulder belt guides.

    5. w/ Rear Seat Side Airbag:


      1. Connect each connector and clamp to the child restraint anchor bracket sub-assembly LH.

  6. INSTALL REAR SEATBACK COVER


    1. Engage the 4 claws to install the 2 rear seatback covers.

      Tech Tips

      Use the same procedure as for the LH side.

  7. INSTALL REAR SEAT CUSHION LOCK HOOK


    1. A01EVL5

      Engage the claw to install a new rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  8. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. w/ Seat Heater System:


      1. Connect the 2 seat heater connectors.

    3. A01EX1E

      Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

    4. Confirm that the rear seat cushion assembly is firmly installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the seat cushion assembly.

  9. INSTALL REAR SEAT HEADREST ASSEMBLY

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  11. INSPECT SRS WARNING LIGHT (w/ Rear Seat Side Airbag)

    Click here