SFI SYSTEM VC Output Circuit

DESCRIPTION

The ECM constantly generates 5 V power source voltage from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A01EUQTE01

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

Tech Tips

Under normal conditions, the MIL is illuminated when the engine switch is turned on (IG). The MIL goes off when the engine is started.

WIRING DIAGRAM

A01EYM7E01
A01EVATE02

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK MIL


    1. Check that the Malfunction Indicator Lamp (MIL) lights up when the engine switch is turned on (IG).

      OK
      MIL lights up.

    NG

    CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the tester on.

    4. Check the communication between the tester and ECM.

      Result
      Result Proceed to
      Communication is not possible A
      Communication is possible B

    B

    GO TO MIL CIRCUIT Click here

    A

  3. CHECK MIL (THROTTLE POSITION SENSOR)


    1. Disconnect the throttle with motor body assembly connector.

    2. Turn the engine switch on (IG).

    3. Check the MIL.

      Result
      Result Proceed to
      MIL does not illuminate A
      MIL illuminates B

      Tech Tips

      Perform "Inspection After Repair" after replacing the throttle with motor body assembly Click here.


    B

    REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY Click here

    A

  4. CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)


    1. Disconnect the accelerator pedal sensor assembly connector.

    2. Turn the engine switch on (IG).

    3. Check the MIL.

      Result
      Result Proceed to
      MIL does not illuminate A
      MIL illuminates B

    B

    REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY Click here

    A

  5. CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))


    1. Disconnect the VVT sensor (for intake camshaft of bank 1) connector.

    2. Turn the engine switch on (IG).

    3. Check the MIL.

      Result
      Result Proceed to
      MIL does not illuminate A
      MIL illuminates B

    B

    REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1) Click here

    A

  6. CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))


    1. Disconnect the VVT sensor (for intake camshaft of bank 2) connector.

    2. Turn the engine switch on (IG).

    3. Check the MIL.

      Result
      Result Proceed to
      MIL does not illuminate A
      MIL illuminates B

    B

    REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2) Click here

    A

  7. CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1))


    1. Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.

    2. Turn the engine switch on (IG).

    3. Check the MIL.

      Result
      Result Proceed to
      MIL does not illuminate A
      MIL illuminates B

    B

    REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1) Click here

    A

  8. CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2))


    1. Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.

    2. Turn the engine switch on (IG).

    3. Check the MIL.

      Result
      Result Proceed to
      MIL does not illuminate A
      MIL illuminates B

    B

    REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2) Click here

    A

  9. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)


    1. Disconnect the throttle with motor body assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E16-5 (VC) or E26-126 (VCTA) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)


    1. Disconnect the accelerator pedal sensor assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A36-4 (VCPA) or A25-56 (VCPA) - Body ground Always 10 kΩ or higher
      A36-1 (VCP2) or A25-59 (VCP2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK HARNESS AND CONNECTOR (VCV1 CIRCUIT)


    1. Disconnect the VVT sensor (for intake camshaft of bank 1) connector.

    2. Disconnect the VVT sensor (for intake camshaft of bank 2) connector.

    3. Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.

    4. Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.

    5. Disconnect the ECM connector.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E26-111 (VCV1) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE ECM Click here