SFI SYSTEM Fuel Pump Control Circuit

DESCRIPTION

When the engine is cranked, the ST (Starter) relay drive signal output from the ignition or starter switch assembly is input to the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input to the ECM with the engine running, the ECM turns Tr1 on continuously.

WIRING DIAGRAM

A01ETFNE04

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    5. Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.

      Result
      Result Proceed to
      Fuel pump operating sound does not occur A
      Fuel pump operating sound occurs B

    B

    READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) Click here

    A

  2. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)


    1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1E-1 - A74-7 (FC) Always Below 1 Ω
      1E-1 or A74-7 (FC) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP)


    1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

    2. Disconnect the fuel pump connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1C-6 - N11-4 (B) Always Below 1 Ω
      1C-6 or N11-4 (B) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)


    1. Disconnect the fuel pump connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N11-5 (E) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT FUEL PUMP


    1. Inspect the fuel pump Click here.


    NG

    REPLACE FUEL PUMP Click here

    OK

  6. CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)


    1. A01EW12E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to No. 1 Integration Relay)

      Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      1B-1 - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)

    OK

    REPLACE NO. 1 INTEGRATION RELAY Click here

  7. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

    5. Check the result when the ignition switch is ON and the engine starts.

      OK
      Ignition Switch Position Starter Signal
      ON Close (OFF)
      START Open (ON)

    NG

    CHECK STARTER SIGNAL CIRCUIT Click here

    OK

  8. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

    5. Read the values displayed on the tester while cranking.

      OK
      Values are displayed continuously.

    NG

    CHECK CRANKSHAFT POSITION SENSOR CIRCUIT Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here