FUEL SYSTEM PRECAUTION


  1. BEFORE WORKING ON FUEL SYSTEM


    1. When disconnecting a fuel line, fuel will spray. So observe the following precautions:


      1. Do not smoke or work near fire when handling the fuel system.

      2. Keep fuel away from rubber or leather parts.

      3. Perform the Discharge Fuel System Pressure procedure below before disconnecting a fuel line to prevent fuel from spraying.

  2. DISCHARGE FUEL SYSTEM PRESSURE

    CAUTION:


    • Perform the following procedure to prevent fuel from spraying before removing any fuel system parts.

    • Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.


    1. Remove the rear seat cushion assembly Click here.

    2. Remove the rear seat cushion lock hook Click here.

    3. Remove the rear floor service hole cover.

    4. A01EXXB

      Disconnect the fuel pump connector.

    5. Start the engine.

    6. After the engine has stopped on its own, turn the ignition switch off.

    7. Crank the engine again and make sure that the engine does not start.

      Tech Tips

      DTC P0171 (Fuel Problem) may be stored.

    8. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    9. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

    10. Connect the fuel pump connector.

    11. Install the rear floor service hole cover with new butyl tape.

    12. Install a new rear seat cushion lock hook Click here.

    13. Install the rear seat cushion assembly Click here.

  3. FUEL LINE


    1. When disconnecting a high pressure fuel line, a large amount of fuel will spray, so perform the following procedure:


      1. Discharge fuel system pressure (See step 2).

      2. Disconnect the fuel pump tube.

      3. Drain the fuel that remains in the fuel pump tube.

      4. Cover the disconnected fuel pump tube with a plastic bag to prevent damage and contamination.

      5. Place a container under the connectors.

    2. Perform the following procedure when disconnecting the fuel tube connector (metallic type):


      1. A01EYCXE03
        Text in Illustration
        *1 No. 2 Fuel Pipe Clamp

        Remove the No. 2 fuel pipe clamp.

      2. A01EWPXE03
        Text in Illustration
        *1 Retainer
        *2 Fuel Hose Clamp
        *3 Fuel Tube Connector
        *a Turn

        Remove the fuel tube from the fuel hose clamp.

        Note

        Do not forcibly bend, kink or twist the fuel tube.

      3. Wipe off any foreign matter on the fuel tube connector.

      4. Hold the fuel tube connector, and then install SST.

        SST
        09268-21011

      5. Turn SST to align the retainer inside the fuel tube connector with the chamfered part of SST.

      6. Insert SST into the fuel tube connector and hold it. Then push the fuel tube connector toward SST.

      7. Mount the retainer of the fuel tube connector onto the chamfered part of SST.

      8. A01EYIFE24
        Text in Illustration
        *1 Retainer
        *2 O-ring
        *3 Fuel Tube
        *4 Fuel Tube Connector
        *5 Fuel Pipe

        Slide SST into the fuel tube connector until it makes a "click" sound, and then disconnect the fuel tube sub-assembly.

      9. Drain the fuel remaining inside the fuel tube.

      10. Cover the fuel tube connector and fuel pipe with plastic bags to protect the disconnected parts.

    3. Perform the following procedure when connecting the fuel tube connector (metallic type):


      1. Check if there is any damage or foreign matter on the fuel pipe connections.

      2. Match the axis of the fuel tube connector with the axis of the fuel pipe, and push the fuel pipe into the fuel tube connector until the fuel tube connector makes a "click" sound. If the connection is tight, apply a small amount of clean engine oil to the tip of the fuel pipe.

      3. A01EXNSE09

        After finishing the connection, check if the fuel pipe and the fuel tube connector are securely connected by pulling on them.

        Text in Illustration
        A01EUL1 Push
        A01ETOA Pull

      4. Inspect for fuel leaks.

      5. Install a new No. 2 fuel pipe clamp.

      6. Install the fuel tube to the fuel hose clamp.

    4. Perform the following procedure when disconnecting the fuel tube connector (quick type A):


      1. A01EV02

        Remove the No. 1 fuel pipe clamp.

      2. Check if there is any foreign matter on the fuel pipe around the fuel tube connector before disconnecting it. Clean it if necessary.

      3. A01EVWRE26
        Text in Illustration
        *1 Retainer
        *2 O-ring
        *3 Fuel Tube Connector
        A01EUL1 Pinch
        A01ETOA Pull Out

        Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

        Note

        Be sure to disconnect the fuel tube connector by hand.

      4. If the fuel tube connector and the fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector out of the fuel pipe carefully.

        Note

        Be sure to disconnect the fuel tube connector by hand.

      5. Check if there is any foreign matter on the sealing surfaces of the disconnected fuel pipes. Clean them if necessary.

      6. Cover the disconnected fuel pipe and fuel tube connector with a plastic bag to prevent damage and contamination.

    5. A01ESPN

      Perform the following procedure when connecting a fuel tube connector (quick type A):


      1. Check if there is any damage or foreign matter on the connecting parts of the fuel pipes.

      2. Line up the 2 parts of the fuel lines to be connected, and push them together until the fuel tube connector makes a "click" sound. If the fuel pipe is difficult to push into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.

      3. After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.

      4. Inspect for fuel leaks Click here.

      5. Install the No. 1 fuel pipe clamp.

    6. A01EYN0E01

      Perform the following procedure when disconnecting a fuel tube connector (quick type B):

      Text in Illustration
      *1 Fuel Tube Connector
      *2 Fuel Pipe
      *3 Retainer
      A01EUL1 Pinch
      A01ETOA Pull Out

      1. Check that there is no foreign matter on the fuel tube connector before disconnecting it. Clean it if necessary.

      2. Pinch the retainer as shown in the illustration, then pull out the fuel tube connector from the fuel pipe.

        Note

        Be sure to disconnect the fuel tube connector by hand.

      3. A01EYII

        If the fuel tube connector and fuel pipe are stuck, pinch the fuel pipe by hand and push and pull the fuel tube connector to disconnect it.

      4. Check if there is any foreign matter on the sealing surface of the disconnected fuel pipe. Clean it if necessary.

      5. Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.

    7. A01ET2V

      Perform the following procedure when connecting a fuel tube connector (quick type B):


      1. Check that there is no damage or foreign matter on the connected part of the fuel pipe.

      2. Align the fuel tube connector with the fuel pipe, then push in the fuel tube connector until the retainer makes a "click" sound.

        Tech Tips

        If the fuel pipe is difficult to push into the fuel tube connector, apply a light coat of engine oil to the tip of the fuel pipe and reinsert it.

      3. A01ETED

        After connecting the fuel lines, check that the fuel pipe and the fuel tube connector are securely connected by pulling on them.

      4. Inspect for fuel leaks Click here.

    8. A01EXF4E01
      Text in Illustration
      *1 Fuel Tube Connector
      *2 Nylon Tube
      *3 Ethylene Propylene Diene Rubber (EPDM) Protector

      Observe the following precautions when handling a nylon tube:

      Note


      • Do not twist the fuel tube connector part of the nylon tube or the fuel tube connector when connecting them.

      • Do not remove the Ethylene Propylene Diene Rubber (EPDM) protector on the outside of the nylon tube.

      • Do not pinch or kink the nylon tubes to prevent fuel leakage.

  4. INJECTOR


    1. A01EWITE01
      Text in Illustration
      *1 O-ring
      *2 Fuel Injector Assembly
      *3 Injector Vibration Insulator
      *4 Fuel Delivery Pipe Sub-assembly
      *5 Cylinder Head

      Install the fuel injector assembly to the fuel delivery pipe sub-assembly and cylinder head as shown in the illustration.

      Note

      Before installing the fuel injector assembly, be sure to apply a light coat of fuel or spindle oil where the fuel delivery pipe sub-assembly contacts the O-ring.

    2. A01EU1KE02
      Text in Illustration
      *1 O-ring
      *2 Fuel Delivery Pipe Sub-assembly
      *a CORRECT
      *b INCORRECT

      Observe the following precautions when removing and installing the fuel injector assemblies:


      1. Never reuse the O-ring.

      2. When placing a new O-ring on the fuel injector assembly, do not damage the O-ring.

      3. Coat a new O-ring with spindle oil or fuel before installing it.

        Note

        Do not use engine oil, gear oil or brake fluid.

  5. FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


    1. A01ETTGE01
      Text in Illustration
      *1 Tube

      Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is welded to the fuel suction plate sub-assembly.

  6. INSPECT FOR FUEL LEAK


    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs Click here.